Code p0340 replaced sensor still won't start

Bad quality replacement. For these sensors always go with quality OEM parts.

P0340 FORD Camshaft Position Sensor Circuit Bank 1 Sensor ...

https://www.autocodes.com > p0340_ford

Repair Information for P0340 Ford code. ... How do I fix code P0340 FORD? ... Ford Factory Service ...

This video may help ... the sensor is underneath the timing belt cover so it is a bit involved to get to ....
https://www.youtube.com/watch?v=RHMe3S7RQ68

Symptoms can include: Hard starting or no start
Rough running / misfiring Loss of engine power Causes
A code P0340 could mean one or more of the following has happened:
a wire or connector in the circuit could be grounded/shorted/broken the camshaft position sensor may have failed the PCM may have failed
there exists an open circuit
the crankshaft position sensor may have failed

Possible Solutions With a P0340 OBD-II trouble code,
diagnosis can be tricky at times. Here are some things to try: Visually inspect all the wiring and connectors in the circuit Check for continuity in the circuit wiring Check the operation (voltage) of the camshaft position sensor Replace the camshaft position sensor as required Check the crankshaft position circuit as well Replace circuit wiring and/or connectors as required Diagnose/replace the PCM as required

Read more at: http://www.obd-codes.com/p0340
Copyright OBD-Codes.com

for better result download the pdf file
2006 HYUNDAI SONATA SERVICE REPAIR MANUAL DOWNLOAD

P0340 code means "Something" is wrong in the timing...
from CMP (Camshaft Position sensor) to the crankshaft bolt.

Very first thing, verify connectors are clean and shiny.
clear all codes, even hard codes.

PO340 is the camshaft sensor, circuit malfunction

PO113 is intake air circuit--high input

PO123 is TPS sensor circuit A high input

Running your car low on oil is never good, how low was it---did it start knocking or did it overheat?
Running on low fuel is never good either, did you run out of gas and burn the fuel pump up?
Why did you replace the starter? Will the engine turn over and try to start? If your engine will crank over, check for spark at the plugs and check to see if you have fuel pressure at the fuel rail...This would be the best place to start troubleshooting.

P1684 The battery has been disconnected within the last 50 starts.

P0340


This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.
Symptoms Symptoms can include:

• Hard starting or no start
• Rough running / misfiring
• Loss of engine power

Causes A code P0340 could mean one or more of the following has happened:

• a wire or connector in the circuit could be grounded/shorted/broken
• the camshaft position sensor may have failed
• the PCM may have failed
• there exists an open circuit
• the crankshaft position sensor may have failed

Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

• Visually inspect all the wiring and connectors in the circuit
• Check for continuity in the circuit wiring
• Check the operation (voltage) of the camshaft position sensor
• Replace the camshaft position sensor as required
• Check the crankshaft position circuit as well
• Replace circuit wiring and/or connectors as required
• Diagnose/replace the PCM as required

I have a 1999 BMW 740 il My SES light came on so I hooked up my OBD code reader p0340 - Camshaft Position Sensor Circuit Malfunction is what came up. so I went to the BMW parts department and bought the Camshaft Position Sensor.
I Replaced the with the new. My SES light was still on so I hooked up the OBD reader again hoping it may reset my SES light but it didn't what did happen is the OBD reader came up with the same code (p0340 - Camshaft Position Sensor Circuit Malfunction) witch is what I just replaced. now I'm at a loss. I'm not sure how to reset my SES light and if I just replaced the Camshaft Position Sensor why dose it the OBD code p0340 still come up. Any suggestions?

P0340 OBD-II Trouble Code
Technical Description
Camshaft Position Sensor Circuit Malfunction

What does that mean? This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

Symptoms
Symptoms can include:

• Hard starting or no start
• Rough running / misfiring
• Loss of engine power

Causes A code P0340 could mean one or more of the following has happened:

• a wire or connector in the circuit could be grounded/shorted/broken
• the camshaft position sensor may have failed
• the PCM may have failed
• there exists an open circuit
• the crankshaft position sensor may have failed

Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

• Visually inspect all the wiring and connectors in the circuit
• Check for continuity in the circuit wiring
• Check the operation (voltage) of the camshaft position sensor
• Replace the camshaft position sensor as required
• Check the crankshaft position circuit as well
• Replace circuit wiring and/or connectors as required
• Diagnose/replace the PCM as required

Also, the cams/crank are out of alignment, thats why you are getting a cam position code (P0340). For more details about your model, you can visit autozone.com (free register)

Hope helped whit this (remember rated this help) Good luck.

p0130 is an oxygen sensor code.
p0340 is your camshaft position sensor code
p0336 is your crankshaft position sensor code

as far as the p0130 code those usually are what i call neglected sensors that do not get replaced when they should be. this sensor is expensive but worth the money as it will help on fuel mileage.

on to the camshaft position sensor, i would start here with this. replace that sensor and when you are replacing it, inspect the sensor and make sure the electrical wires going into it are in good shape. after replacing those 2 sensors, go to a parts store who can erase your codes to turn the light off and then let us know if it comes back on and then we will go from there on the repair.