Were is the windshield washer fluid sensor 2005 ford freestar ?

You need to find out which oxygen sensor needs to be replaced, your vehicle could have 2 or 3. They are located in the exhaust system either in the exhaust manifold or the exhaust pipe before the catylitic converter and one after the catalytic converter. http://www.rockauto.com/en/catalog/ford,2005,freestar,3.9l+v6,1430707,exhaust+&+emission,oxygen+(o2)+sensor,5132 Where is the o2 sensor on 2005 ford freestar 3 9

images for Ford Freestar Washer fluid bottle

How To Install Replace Windsheild Washer Reservoir Bottle ...

? 13:32
https://www.youtube.com/watch?v=kA38mzgMCkk
Jun 11, 2012 - Uploaded by 1A Auto Parts
How To Install Replace Windsheild Washer Reservoir Bottle FordEscape ... a broken, damaged, split or leaking windshield washer bottle.

ON the washer resivor

That is a Torque Converter Clutch code it is reading that the circuit performance is stuck off. try these solutions one at a time. 1. check transmission fluid level. 2. add lucus trans treatment. 3. replace sensor. 4 replace torque Converter. Erase code after each action.

The hole where the windshield wiper fluid comes out must be plugged with debris. Get yourself a couple toothpicks and wet them - then widen the hole with them. Be careful not to break one off in the hole. That should solve your problem.

Many modern cars have the windshield washer fluid pump in the tank for the washer fluid.

Check the transmission fluid level. if there is none, or it is low, the car won't move. Use caution when buying transmission fluid. there are different types for different cars.

I have 2007 only. please rate as solved if this is what you needed. good luck.

SECTION 501-16: Wipers and Washers 2007 Freestar/Monterey Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/27/2006
Wiper Motor — Windshield Printable View (104 KB) Removal

1. Remove the windshield wiper arms.

1. NOTE: Disconnect the washer hose before removing the cowl panel grille.
   Remove the pushpin-type retainers and the cowl panel grille.

1. Remove the washer hose grommet from the cowl panel and position aside the washer hose.

1. If equipped, remove the A/C air inlet filter.

1. Remove the 9 cowl panel bolts and position aside the cowl panel.

1. Disconnect the windshield wiper motor electrical connector.

1. Remove the cowl panel from the vehicle.

1. Remove the 4 bolts and the windshield wiper motor.

Installation

1. Position the wiper pivot arms on the windshield wiper motor and install the bolt.
   • Tighten to 15 Nm (11 lb-ft).

1. Install the 3 windshield wiper-to-cowl panel bolts.
   • Tighten to 15 Nm (11 lb-ft).

1. Position the cowl panel in the vehicle and connect the windshield wiper motor electrical connector.

1. Install the washer hose and grommet in the cowl panel.

1. Install the 9 cowl panel bolts.
   • Tighten to 6 Nm (53 lb-in).

1. If equipped, install the A/C air inlet filter.

1. Position the cowl panel grille in the vehicle and connect the washer hose.

1. Install the pushpins.

1. Install the windshield arms and nuts.
   • Tighten to 27 Nm (20 lb-ft).

1. Cycle and park the windshield wipers to check for correct alignment.

it is in front of the windshield where the air is pulled in, just run the blower on high and listen.