Question about 2004 Ford F350

Open Question

Where can I find the jack pin for ford mirror f350

2004 FORD F-350 SUPER DUTY 5.4L

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 11 Answers

SOURCE: how to replace outside mirrors on a 2002 ford f-250 super duty

you need to remove door trim panel there are (2) 7mm screws that hold panel on .. 1 is behind the lower red light lens and the other is behind switch panel for the power window switch . remove both screws and remove small black panel above door trim by pulling strait off .(now there are (4) 11mm nuts the hold mirror on 2 are behind the small rubber plugs in front of door that you can see with panel on and the other 2 are under panel that you can see after panel is removed . the wiring need to be disconneced you may have to remove speaker for acess to feed new wiring down into the door good luck

Posted on Mar 11, 2009

Ad
motor1258

Mike Butler

  • 6674 Answers

SOURCE: 1999 Ford F-250 Super Duty 6.8 liter v10 is

You'll have to drain system down when cooled off, remove any brackets in your way such as power steering reservoir holding bracket, then remove 2 bolts holding the housing, and remove it. Rad hose should be o.k. to leave on, but if it creates a problem, remove it as well. I'd install a new thermostat and "o" ring complete,then a new gasket as well. Clean all surfaces well before re-installing. Replace any bracket(s) you removed to access housing, after housing is installed. Remember, air valve on edge of thermostat goes in 3 oclock position when re-installed. Also a reminder as well, spring on thermostat goes down when re-installed. After all is re-assembled, re-fill coolant and start engine and run with heater on to bleed out all air. Leave rad cap off and pay attention to temperature gauge and when you see it getting to normal operating temperature, watch flow in rad for increased flow, indicating thermostat opened and coolant is circulating properly. Wait until you see that flow increase 2 or 3 times, and air should be out of system, and top up coolant in rad, put cap back on, and check that return bottle is at proper level as well. Keep an eye for any leaks, and re-check return bottle periodically for first little while, just to be sure all is good. Note: some only use the "O" ring as a seal, and no gasket is required, but just check that at autoparts place where you get part.

Posted on Dec 28, 2009

philgoodno1

  • 41 Answers

SOURCE: 1999 ford f250 super duty 4x4 will go into 4

transfer case selector switch or equivlent to is bad or connectors to the switch is bad dose it do only when it rain or moisture underneath.

Posted on Jan 19, 2010

William Desautels

  • 102 Answers

SOURCE: My horn does not work on my 2003 Ford f250 super duty PU truck.

The horn location is on the radiator support.

Posted on Mar 08, 2010

Fixya_sucks

Expert

  • 21 Answers

SOURCE: I cannot get the side

- Adjust the mirror so the mirror glass is in as far as it will go (meaning if you were looking in the mirror you would see the side of the truck)

- Look inside the mirror housing
- Locate silver clip
- Using a flat screw driver, push the clip in
- Lenses will pop out on the outside
- Remove bulb
- Replace bulb
- Snap back together when new bulb in place.

Posted on Oct 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is mirror wiring for plugins?


Installing 08 mirrors on 01 Superduty, looking for wiring diagrams ...

www.ford-trucks.com > ... > Super Duty & Heavy Duty
Aug 12, 2008 - Installing 08 mirrors on 01 Superduty, looking for wiring diagrams Super Duty ... 2013-2014 mirror plug pin outs, SUPERDUTY_08, Super Duty ... Power/Heated/Lighted Tow Mirror upgrade...
Jul 24, 2012
F250 Paddle to towing mirror installation
Dec 20, 2010
Towing Mirror Wiring Harness Adaptor
Sep 15, 2010
Towing mirrors
Apr 16, 2010
More results from www.ford-trucks.com

Nov 19, 2015 | 2000 Ford F350 Super Duty Super Cab

1 Answer

2002 Ford F250 Super Duty SuperCab l/h power mirror intsallation


http://rogerweber.blogspot.com/2006/09/replacing-ford-f-250-super-duty-side.html try this website its step by step instructions and illustrations. hope this helps

Nov 19, 2011 | 2002 Ford F250 Super Duty SuperCab

1 Answer

2002 Ford F250 Super Duty SuperCab l/s power mirror installation


http://rogerweber.blogspot.com/2006/09/replacing-ford-f-250-super-duty-side.html try this website. hope it helps

Nov 19, 2011 | 2002 Ford F250 Super Duty SuperCab

1 Answer

2002 ford f250 super duty left side mirror installation


http://rogerweber.blogspot.com/2006/09/replacing-ford-f-250-super-duty-side.html try this website, hope it helps

Nov 19, 2011 | 2002 Ford F250 Super Duty SuperCab

2 Answers

I have malfunctioning electric-driven exterior towing mirrors on a 1999 ford f-350. How to diagnose/fix? Mirrors respond only to right adjust; no response on up/down or left adjust.


there is a separate motor for up/down and another for left/right adjust. The glass is serviceable but not the motors, built into the frame of the mirror body.

SECTION 501-09: Rear View Mirrors 2000 F-Super Duty/Excursion/Motorhome Chassis Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
NOTE: Left-hand dual arm mirror with heat shown, non-heated and aero mirrors similar.
  1. Position the exterior rear view mirror glass in the full down position.
  1. Grasp the top and carefully pull the mirror glass away from the mirror housing.
  1. Disconnect the electrical terminals (if equipped) and remove the exterior rear view mirror glass.
Installation
  1. Remove the jack pins from the mirror glass back.
  1. Remove the sealing boots.
  1. Install the jack pins in the sealing boots.
  1. Install the jack pins and sealing boots.
    1. Install the jack pins in the mirror housing.
    1. Install the sealing boots so the boot shoulder is under the mirror collar.
  1. Loosely install the glass.
    1. Connect the electrical wiring to the electrical terminals (if equipped).
    1. Position the friction pins in the mirror housing.
    1. Align the jack pin locating tabs to match with the mirror glass back.
  1. Using a flat hand, press on the center of the mirror glass until seated on the center pivot of the mirror housing.
    • Press the mirror glass toward one of the jack pins until snapped in place.
    • Repeat for second jack pin.

Jan 13, 2011 | Ford F-350 Cars & Trucks

2 Answers

I cannot get the side mirrors apart to change the bulbs on my 2008 ford super duty truck. The mirrors are heated.


- Adjust the mirror so the mirror glass is in as far as it will go (meaning if you were looking in the mirror you would see the side of the truck)

- Look inside the mirror housing
- Locate silver clip
- Using a flat screw driver, push the clip in
- Lenses will pop out on the outside
- Remove bulb
- Replace bulb
- Snap back together when new bulb in place.

Oct 10, 2010 | 2008 Ford F 250 Super Duty 4WD

2 Answers

Ford F250 SD, 2wd. Replacing front bearing


If you have front disk brakes you have to remove the brake caliper to get the rotor off.

Oct 03, 2009 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

How to replace outside mirrors on a 2002 ford f-250 super duty


you need to remove door trim panel there are (2) 7mm screws that hold panel on .. 1 is behind the lower red light lens and the other is behind switch panel for the power window switch . remove both screws and remove small black panel above door trim by pulling strait off .(now there are (4) 11mm nuts the hold mirror on 2 are behind the small rubber plugs in front of door that you can see with panel on and the other 2 are under panel that you can see after panel is removed . the wiring need to be disconneced you may have to remove speaker for acess to feed new wiring down into the door good luck

Mar 10, 2009 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Replacement of Mirror/Assembly, 2004 Ford E350 Super Duty


Exterior Mirror Removal and Installation
NOTE: Aero mirror shown, dual arm similar.
Manual mirrors
  1. Remove the mirror sail cover to gain access to the exterior mirror retaining nuts.
Power exterior mirrors
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. If equipped, remove the front door speaker.
  1. Remove the front door watershield.
All exterior mirrors
  1. Remove the rubber plugs and dust shield.
Power exterior mirrors
  1. Disconnect the electrical connector(s).
    1. Disconnect the power exterior mirror electrical connector.
    1. If equipped, disconnect the heated exterior mirror connector.
All exterior mirrors
  1. Remove the nuts and remove the exterior mirror.


  1. To install, reverse the removal procedure.
  2. 01cb1f9.gif

Jan 08, 2009 | 2007 Ford E-350 Super Duty Length XLT

2 Answers

How to remove mirror glass 2008 ford f350


here's 2003, don't have 2008

Removal
NOTE: Left-hand dual arm mirror with heat shown, non-heated and aero mirrors similar.
All exterior mirrors
  1. Position the exterior mirror glass in the full down position.
  1. Grasp the top and carefully pull the exterior mirror glass away from the mirror housing.
8157e6e.gif
  1. Disconnect the electrical terminals (if equipped) and remove the exterior mirror glass.
Power exterior mirrors
  1. Remove the jack pins from the exterior mirror glass backing plate.
    • Use pliers to grasp the jack pins at the base to remove.
429f568.gif
Installation
Power exterior mirrors
  1. Remove the sealing boots from the exterior mirror motor.
a8bd649.gif
  1. Install the jack pins in the sealing boots.
869a220.gif
  1. Install the jack pins and sealing boots.
    1. Hold the legs of the jack pins and push the jack pins back into the exterior mirror housing.
    1. Install the sealing boots so the boot shoulder is under the mirror collar and turn each jack pin until the head of the jack pin is aligned with the slots in the sockets on the backing glass plate.
95e6577.gif
All exterior mirrors
  1. Place the new exterior mirror glass assembly down on a smooth firm surface.
  1. Align the friction pins vertically to the exterior mirror glass backing plate socket and push down to snap the pivot ball into the socket.
52fef14.gif
  1. s3o~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not over heat the exterior mirror glass backing plate. Heat only until backing plate is warm to the touch.
    Using the special tool, warm the main pivot sockets in exterior mirror glass backing plate.
ed69017.gif
  1. Loosely install the glass.
    1. Connect the electrical wiring to the electrical terminals (if equipped).
    1. Position the friction pins in the mirror housing.
    1. Align the jack pin locating tabs to match with the mirror glass back.
  1. Using a flat hand, press on the center of the mirror glass until seated on the center pivot of the mirror housing.
    • Press the mirror glass toward one of the jack pins until snapped in place.
    • Repeat for second jack pin.
a10e39d.gif
Power exterior mirrors
NOTE: If the jack pins do not engage, they may not be aligned correctly. Remove the exterior mirror glass, align the jack pins to the slots in the sockets and repeat the installation procedure.
  1. NOTE: The jack pin should click while manually adjusting the exterior mirror glass.
    Tilt the exterior mirror glass to the full outboard position and then press on the outer side of the class until the in/out jack pin snaps into the socket on the exterior mirror backing plate.
  1. NOTE: The jack pin should click while manually adjusting the exterior mirror glass.
    Tilt the exterior mirror glass to the full down position and then press on the outer side of the class until the up/down jack pin snaps into the socket on the exterior mirror backing plate.

Nov 14, 2008 | 2008 Ford F-350

Not finding what you are looking for?
2004 Ford F350 Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...