Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on Sep 19, 2014

Nissan s14 security light stays on constant

Security light next to hazard switch on dash, the little red led that usually blinks just stays on constantly...

5 Related Answers

Anonymous

  • 4669 Answers
  • Posted on Mar 19, 2009

SOURCE: 97 Lumina dash warning lights stay on

For the security light you need to replace the ignition lock cylinder or bypass the security system. For the other two, you need to have the car scanned to see what codes are in the ecm and the abs module.

Ad

Paul Hutchinson

  • 909 Answers
  • Posted on Jul 19, 2009

SOURCE: red light next to hazard light button blinks when

If it's a tiny red L.E.D. like a car alarm indicator, then it's to let you know the imobilizer is set, factory fitted and set to work from your key sensor(built into the ignition switch and key)

Philip Armitage

  • 437 Answers
  • Posted on Aug 23, 2009

SOURCE: 1997 LeSabre- Security light in dash is constantly

ok the security light is on because it isn't reading the chip pellet in the key. The problem with the is usually either bad key, bad pickup in the cylinder, or bad paskey unit. if it is the key or the cylinder then you can bypass the unit by adding a resistor to match the key resistance and attach it to the violet and white wires at the bottom of the column. I do alot of bypasses on these passkey units, it works wonderful.

Your stalling however sounds like a different problem.. since the security system only disables the starting feature and not the running of the vehicle. But with the 3800 engine the cranshaft sensor or sensor wiring, as the engine gets hot causes shorting to the computer and shuts engine down. I would look into that to solve your problems.

Testimonial: "Thanks! I have had the crank sensor replaced twice in the past 2 months, the new one just last wk.Also cam sensor, coils, wires and plugs. AArrg!"

tony tiler

  • 45 Answers
  • Posted on Oct 22, 2009

SOURCE: hand brake light on dash stays on constantly

it sounds like the switch as broke were the hand brake lever is what you need to do is were the hand brake is there should be some sort of caseing around it you need to unscrew this in there they will be a black thing that when you put the hand brake down it will sit on this button to make it go out then when you pull it up it will come on again. so you need to find it check all wires are on and that the brake is sitting on it right if not replace it.. hope this helps you please leave feed back if it does..

Anonymous

  • 130 Answers
  • Posted on Mar 26, 2011

SOURCE: oil light comes on and blinks then goes off .

Have you checked your oil level? This light indicates either an oil level problem or an oil pressure problem.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Hazard lights won't turn off, all other lights work fine.

The lights are blinking or stay lit on the dash. Blinking is a bad switch, just coming on is a bad ground at the front.
0helpful
1answer

Where is the hazard light switch ?

it usually depends on what you are driving some are on the dash some are in the middle of the dash around the radio some are on the searing column. what you are looking for is usually a red button with a triangle on it.
0helpful
1answer

My brake lights would not shut off,I had to use hazards to get home. Then they stopped blinking and also my turn signals done the same. 95 nissan hardbody pickup 2-wheel drive

the brake light switch down below the dash on the pedal is stuck or out of alignment. The little plunger or spring lever in the switch is stuck in. Find it and spray it with W-D 4O as it may be full of lint
0helpful
1answer

I have a 2001 Saab 9.3 convertible. The red security light on the dash won't blink, the door chimes when I open it and the key is out and lights are off and my key faub won't work and has new battery. I...

Seeing the date that you posted this, I wonder if this has been resolved?

For your car, if the remote does not open the car door after the battery in the fob has been replaced, do this.
1. Get next to the car with doors locked
2. Push the Unlock button 4 times in succession as you count, one, two...
3. The remote receiver should recognize your fob now

As for the dash LED, it may be unplugged somewhere. The DI cassette has little to do with it. LEDs have an ginormous life span and should not go dead - at least for the life of your car. Does it EVER flash?
1helpful
2answers

Where is signal flashing relay located on car? my signal light just stays on when turning left or right and does not flashr blink.

TURN SIGNAL/ HAZARD FLASHER MODULE IS BELOW LEFT SIDE OF DASH. IF THE HAZARD LIGHTS WORK YOU CAN LISTEN FOR THE CLICKING.
7helpful
2answers

Red light next to hazard light button blinks when car is off and no key, doors closed, is not hazard lights

If it's a tiny red L.E.D. like a car alarm indicator, then it's to let you know the imobilizer is set, factory fitted and set to work from your key sensor(built into the ignition switch and key)
1helpful
1answer

We replaced the car's battery and now the dash board lights blink

Under the dash on drivers side is the black box for the security system. If you look on the box there is a little red button. Push the button for a couple of secounds and it will click and stop your marker lights and dash lights from flashing. It is a stock anti theft part of the security system. Hope this helps.
0helpful
1answer

My turn signals dont work but my hazard lights are blinking. everything else in my car works just fine. my brother says that it was the hazard switch thats shorted out and the relay is causing a clicking...

Did the battery get changed recently? There is a small black box under dash near steering colom that has a little red button on it. Press the little button for a few secounds allowing it to reset the security system. It should stop your marker lights from flashing. It was a stock security for that year. The box is about 4 inch square and is usually just under dash near your knee. Good luck.
3helpful
2answers

My car alarm is blinking but the remote doesn't work. I already replaced the battery to the remote so I know that's not the problem. If I open the car the alarm goes off and doesn't allow me to start the...

You need to first look under the drivers side dash area near the hood release/fuse panel area and see if there is a valet switch. The switch will look like a little toggle or a push switch. After you locate it, turn the ignition switch to the on position(dont start it) and flick the valet to the opposite position it is in now. If done correctly in most cases the red system light will stay a constant instead of off or blinking indicating you are in valet mode. Next try to start the engine. If this doesnt work you need to remove the alarm system and repair the ignition switch wiring or replace the electrical portion of the ignition switch. The aftermarket alarm cuts into the ignition switch wires and bypasses the start circuit through the alarm module. When disarmed the alarm completes the circuit and allows the car to start. Good luck hope this helps and please rate this.
Not finding what you are looking for?

182 views

Ask a Question

Usually answered in minutes!

Top Nissan Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...