Gear incorrect p0732 - 2001 Audi A4

P0141 o2 sensor heater circuit malfunction bank 1 sensor 2
po455 evaporative emission control system leak Gross leak
po303 misfire cylinder three
p0732 gear two incorrect ratio
p0734 gear 4 incorrect ratio

P0723: Output Speed Sensor Intermittent Signal
Read more: http://www.autocodes.com/p0723.html

P0732: Gear 2 Incorrect ratio
Read more: http://www.autocodes.com/p0732.html

P0700 transmission control system malfunction (failure)
P0732 gear 2 incorrect ratio
P0734 gear 4 incorrect ratio

Check level and conditions of fluid

The P0732 means Gear 3 Incorrect Ratio, hope it can help you.
___________
autocom cdp pro

P0735 FORD - Automatic Transmission Incorrect Fifth Gear Ratio Incorrect Possible causes - Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit
P0732 FORD - Automatic Transmission Incorrect Second Gear Ratio Incorrect All - causes would be the same as above with ALSO Probable bad valve body - and or pressure solenoids. Probable bad clutch band. If the fluid is ok and if you have tried changing the fluid and filter to no aval. Is it time to think about a transmission repair at a local transmission shop. Sorry.

p0732
incorrect gear ratio,second gear

p0735
incorrect gear ratio, fifth gear

p1762
are you sure this is the code number it is a manufacturer-specific code. and i'm not seeing it in my bood check to see if you have the right numbers on it.

P0715 Input/Turbine Speed Sensor Circuit Malfunction
P0731 Gear I Incorrect ratio
P0732 Gear 2 Incorrect ratio
P0734 Gear 4 Incorrect ratio
It seems like you were having an issue with your transmission but if you cleared your light and it has stayed off I would just keep a close eye on it.

P0732 and P0734 indicates gear ratio errors in 2nd and 4th gears, basically no 2nd and 4th gear. The one thing 2nd and 4th gear has in common is the band, the band is known to break, this is a common failure with this transmission and happens on a regular basis.

You need to remove the transmission to repair it.

Trouble Code: P0732 (4.6L V8 VIN W Auto)
Incorrect Second Gear Ratio Print this code data Number of Trips to Set Code: 2
OBD II Monitor Type: CCM Details
Indicators: MIL Details

• CCM Details

Trouble Code Conditions:
Engine started, vehicle operating with 2nd Gear commanded "on", and the PCM detected an incorrect 2nd gear ratio during the test.

Possible Causes:

• 2nd Gear solenoid harness connector not properly seated
  
• 2nd Gear solenoid signal shorted to ground, or open
  
• 2nd Gear solenoid wring harness connector is damaged
  
• 2nd Gear solenoid is damaged or not properly installed
  

Refer to the mechanical section to diagnose transmission concerns


Trouble Code: P0732 (5.4L V8 VIN L Auto)
Incorrect Second Gear Ratio Print this code data
Number of Trips to Set Code: 2
OBD II Monitor Type: CCM Details
Indicators: MIL Details

• CCM Details

Trouble Code Conditions:
Engine started, vehicle operating with 2nd Gear commanded "on", and the PCM detected an incorrect 2nd gear ratio during the test.

Possible Causes:

• 2nd Gear solenoid harness connector not properly seated
  
• 2nd Gear solenoid signal shorted to ground, or open
  
• 2nd Gear solenoid wring harness connector is damaged
  
• 2nd Gear solenoid is damaged or not properly installed
  

Refer to the mechanical section to diagnose transmission concerns.

P0732 Gear 2 Incorrect ratio
This is probably something you are going to have to take to your mechanic and have them look at for you.