95 GMC Jimmy 4L60E no 2nd or OD 4L60E

1 Ck A/T fluid level & quality
2 Scan/ck for code(s)
3 With scan tool connected,road test vehicle/Ck parameters....
....time for a pro !!

If you need further help, reach me via phone at https://www.6ya.com/expert/ralph_2f0886b7d6af32ce

there is actuators for each gear i would look into testing those

Sounds like you have lost a shaft(sungear) in the transmission. It can be repaired, but you can get a used one for less than half the cost. Repair-$1300.00+, used - around $500.00

It winds up in 1st and then shifts right from 1st into 3rd. Then never shifts into 4th. Plus rev is gone. You broke the sun shell. The transmission will need to rebuilt or replaced.

Hi, It may be in LIMP mode.

What is "limp-home mode" ? This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Common failures on 4L60E, symptom any possible repair:

Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under-hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter :ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Trans seems noisy when moving in 1st and Reverse, noise goes away instantly if you shift to N or the trans goes into 3rd gear: Reaction planetary is worn out due to high miles or insufficient lubrication. Not a critical failure, but not a good sign either. R&R sooner rather than later.

3rd gear starts, can manually shift through all gears. When car has been turned off for a bit, then back on it will run normally.: VSS dropoff w/ Hi-stall converter. The rpms are too high, but VSS is showing no movement. Happens after a tire burning take-off. Doesn't store a code, will not throw a CEL (I've heard that it will store a code if it happens 3 or more times). Cure: Reprogram PCM for VSS dropoff -- PCMforLess knows about it.

If you can get the Jimmy for no more then $500.00 and the engine sounds good and body is good, you may want to invest in the repair of the jimmy. Also note that to have a close look at the fuel line along the frame on the drivers side just by the back doors, the line is know to corroded there on all the SUV's

IF the abs dash light is on and if the speedometer is sluggish or not working at all, it is probably a bad speed sensor on the transmission. and easy fix under $40 for the part. Mine was stuck in second gear for a while then worked then it stuck in first gear and i had the CHECK ENGINE light on.

Do all the forward gears work or does it rev high in 1st and skip 2nd and shift right to 3rd?

Check that the OD solenoid on the torque converter is good still. When the R4 wont go into OD you have no more gears than 1st an 2nd. If the OD clutch drum was relaced if it was burnt, that will make a problem also. You have to have OD in order for these babies to work right.

You might want to try this if its got a kick down cable unhook it from throutle body and pull it out as far as you can and let it snap back, do this a few of times, sometimes a valve gets hung up inside valve body of trans. and won't let it shift. If that don't help you may have to pull pan to dislodge it if thats the problem. chk. the plug on trans. (Its a 4 wire white plug) with test light with key on to see if there is power down there one will be hot, thats for overdrive, now on top of intake in front throutle body there is a sending unit that looks like a temp. sending unit with a 2 wire plug on it that sends a signial down to that plug when engine gets to temp. to let it shift to overdrive. Maybe this will help, or give you some ideas.

no power stuck in 3rd gear electric shop unless youve burnt it up good luck...www.TransmissionGarage.com