Removing middle seats-procedure

Look for the bolts (under the carpet) & remove them, should come right out.

Yes of course you can remove the seat. There is a pull at the rear of the seat in the middle (down on the frame) The pull is a loop of material. You need to pull that up with solid force, this will release the lock so you can tilt your seat forwards. Once the seat is rotated forward enough, you will be able to lift the seat out.
I leave my seat out behind the drivers seat most of the time for easy access into the back and just putting stuff in the car. Also, the side clearance height is higher than the rear hatch height.

On these case go with the solved problems related to these issue.

Click the link below and follow the procedure:-----
1994 Lexus GS300: Power seat will not go back? http://howtobyme.blogspot.in/2012/05/1994-lexus-gs300-power-seat-will-not-go.html

-----------
1997 Toyota Avalon: Power Seat will not Move back? http://whatisbyme.blogspot.in/2012/05/1997-toyota-avalon-power-seat-will-not.html

----------
1998 Chevrolet Corvette: Power Seat Control Now Working? http://schematicsdiagram.blogspot.in/2012/04/1998-chevrolet-corvette-power-seat.html

-----------
Power seat will not go Forward http://repairhelpcenter.blogspot.com/2012/10/power-seat-will-not-go-forward.html

-----------
Replacing power adjustable bucket seats to both heated and cooled seats?

http://schematicsdiagram.blogspot.com/2011/12/replacing-power-adjustable-bucket-seats.html

-------------
Volvo Seat Removal with Heated Seats? http://schematicsdiagram.blogspot.in/2012/07/volvo-seat-removal-with-heated-seats.html

-------------

How to Remove Rear seat on Rover 600? http://repairhelpcenter.blogspot.com/2012/01/there-are-3-10mm-bolts-at-back-of-seats.html

---------
How to remove Seat? http://repairhelpcenter.blogspot.com/2011/11/how-to-remove-seat-on-acura-integra.html

-----------
These will help.
Thanks.

door panel must come off.

go here for villager help

http://groups.yahoo.com/group/villagerquest/

Section 01-05: Trim, Interior 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door
Front
Removal

1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
   

1. CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
   Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).
   
   
   
   
   

1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel.
   

1. Pull the shop rag back and forth to release the window regulator handle clip.
   
   
   
   
   

1. Remove the three cover caps and front door trim panel screws.
   

1. Remove the one front door trim panel capped screw from the door pull handle.
   

1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
   

1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
   

1. Remove the front door trim panel.
   

Installation
To install, reverse the removal procedure. Body Side
Removal

1. Gently pry loose the body side door latch handle bezel and remove it.
   

1. Slide a suitable tool behind each of the retainers and twist the tool to disengage the body side door trim panel from the body side door (24622).
   
   
   
   
   

Installation
To install, reverse the removal procedure. Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal

1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
   

1. Remove the front door watershield by carefully detaching it from the adhesive.
   

Installation

1. Install the front door watershield in the proper position and press firmly at the adhesive areas. If necessary, use additional adhesive to ensure an adequate seal.
   

1. Install the Front Door Trim Panel . Refer to the installation procedure in this section.
   

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

please rate highly if this is what you need

Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Cushion, Rear Removal and Installation

1. Release pin from locks by pressing release button under rear seat cushion.

1. Pull rear safety belt and buckle (60044) through openings in rear seat cushion pad and frame (600A88) and remove rear seat cushion pad and frame .

1. To install, reverse Removal procedure.
   

----------------------------------------------
Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Back, Rear Sedan
Removal

1. Remove rear seat cushion as outlined.

1. Remove rear seat bolster. Refer to Section 01-05 .

1. Remove rear seat bolster mounting bolts. Remove bolster assembly.
2. Remove four seat back to package tray retaining bolts.

1. Remove seat back.

1. To install, reverse Removal procedure.

it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal

1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
   

1. Slide the bench seat forward to the center row seating position.
   

1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.
   
   
   
   
   

1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.
   
   
   
   
   

1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.
   
   
   
   
   

1. Remove the bench seat from the vehicle through the body side door opening.
   

http://autos.groups.yahoo.com/group/villagerquest/

it's usually called the trans mount cause that's what's on that side.

Section 02-03: Engine and Transaxle Mounting 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Support Insulator, Front Transaxle Removal

1. Remove the battery (10655). Refer to Section 14-01 for the removal procedure.
   
2. Remove the Engine Air Cleaner (ACL) (9600). Refer to Section 03-12 for the removal procedure.
   
3. Remove the radiator coolant recovery reservoir (8A080). Refer to Section 03-03 for the removal procedure.
   
4. Remove the battery tray (10732). Refer to Section 14-01 for the removal procedure.
   
5. Support the transaxle with a floor jack.
   
6. Remove the front transaxle support insulator through bolt and nut.
   
7. Remove the three front transaxle support insulator bolts and the front transaxle support insulator.
   

-----------------------------------------------------------
Support Insulator, Rear Transaxle Removal

1. Remove the rear transaxle support bracket. Refer to the procedure in this section.
   

1. Raise and support the vehicle.
   

1. Remove the three rear transaxle support insulator nuts.
   
   
   
   
   

1. Lower the vehicle.
   

1. Remove the rear transaxle support insulator from the vehicle.
   

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.

fold top seat down first
then there is seat clip push seat forward with upward motion
this releases back floor clamps once released pull seat back this releases the front clamps then pull seat out of back door