Ford festiva cv boots

You should be able to get a universal CV boot. Obviously, you would have to check the dimensions before buying it.

Have a look on Ebay. A supplier of CV boots should be able to sort one out for you.

impala cv boot

That will be your CV joint, inner or outer, easy fix.

Yes the early subaru's all use the same front and rear axles
Fronts are easy to change. rears are not.
The only difference in the early style axles that use pin on inner joints are the outer joints with abs rings.

the reason for this is that the oem boot is not at all simple to replace, the whole cv shaft would have to be removed. the universal boot is thin and flexible to try to accomodate many variations of joints without having to remove the whole shaft. only suggestion I could make would be if your going to go thru the trouble to pull the whole shaft would be to totally replace the whole shaft. seriously its not a 30 min job, your looking at probably 3 to 4 hrs or more and thats if you have all the correct tools readily accessible. they don't come out easy, and rarely go back in easy.

The outer CV-joint boot can be serviced or replaced by removing the inner CV-joint. Click this link below for replacing instructions:--- http://repairhelpcenter.blogspot.com/2011/10/how-to-replace-front-drive-axle-cv.html ----------- This will help.Thanks.Helpmech.

How to Replace a CV Boot
( DIY Complexity: Hard / Time: 3.2 hours )

Parts:
1. CV Boot
2. CV Boot Clamp Kit

Tools:
1. Mallet Hammer
2. 3/8 in. Drive Ratchet
3. Combination Wrench Set
4. Floor Jack
5. Flashlight
6. Flat Head Screwdriver
7. Socket Set
8. Tire Iron

Steps:
Step 1 Secure the vehicle on a level surface, making sure the vehicle will not roll or lean too much when jacked up.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Lift up the front of the vehicle using a jack.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

Step 3 Secure the vehicle with jack stands on both sides for safety before starting any work. The pinch welds and the frame are the two best locations. Do not rely on the jack to hold the vehicle up while working.
o Tip: Try to find a flat, level, and strong surface to put the jack stands.

Step 4 Find the correct size socket and large ratchet or tire iron and turn the wheel lug nuts counter clockwise. Remove the front wheels.
o Tip: It is a good idea to try and break the lug nuts free before you jack the wheels off the ground. This way they you will not spin the front wheels or put stress on the transaxle.
o Tip: Lug nuts fasten the wheel to the hub and may be on very tight. To gain more leverage, use a breaker bar to loosen the nuts.

Step 5 Inspect the CV boot for damage.
o Tip: The CV joint may be worn if the boot is damaged. Thoroughly inspect the CV joint assembly before installing the new boot. If the CV joint is damaged, replace the entire CV joint axle assembly.

Step 6 Mark the axle for installation reference. Remove the CV joint axle assembly.

Step 7 Using a bench vise, hold the shaft of the CV joint secure so that you can separate the CV joint from the shaft. Remove the CV boot clamps.

Step 8 Slide the CV boot off the outer CV joint.

Step 9 Using a rubber mallet, knock the CV joint off of the axle shaft.

Step 10 Remove the old boot from the CV axle shaft and wipe off any old grease. Clean the sealing surface on the CV joint.

Step 11 Fill the CV joint with grease and get it ready to slide back onto the shaft.

Step 12 Slide the new boot onto the shaft but do not tighten the inner clamp yet. Install a new retaining clip before putting the joint and axle together.

Step 13 Slide the CV joint back onto the axle shaft completely.

Step 14 Pack the boot with grease and slide the boot over the CV joint housing. Secure the boot with new clamps.

Step 15 Install the CV joint and axle back into the vehicle in the reverse order that it was removed.

Step 16 Mount the wheel back onto the hub assembly.

Step 17 Tighten lug nuts in a star pattern and torque to suggested manufacturer specifications in the vehicle owner’s manual.

Step 18 Remove jack stands.

Step 19 Lower vehicle with jack until it is securely on the ground.

Step 20 Drive the vehicle to make sure that any noises are no longer present and that there are no indications of wearing parts. Before road testing, visually inspect the area you have worked on to make sure everything is tightened and assembled properly.

Hope help with this (remember rated and comment this help).

you can replace just the outter but you may want to replace the whole axle alot easier

Hello, the boot kits are only available after market and they are more expensive than what you can get the entire CV axle unit for on ebay if you wait for one to show up. I have bought mine on ebay for about $50 brand new. If you're just worried about the ripped boots, you can make your own with an old inner tube and use hose clamps to seal the ends. So basically its up to you how much money you want to spend. I like to fix things right, but I never overlook a cheap and easy solution to save money.

Hello, the front light bulbs are easily changed by twisting the plastic holder in the back of the lamp that holds the bulb counter-clockwise. You turn it about a 1/4 turn and then it pulls out and you can switch bulbs. Do not touch the new bulb with your fingers because oil from your fingers will cause the bulb to burn out quickly.