20 Most Recent 2006 Chevrolet Impala Questions & Answers

What does the word CAL mean that shows on the dash

CAL stands for Calibrate. The IPC (instrument panel cluster) needs to be recalibrated. This could becaused by a battery/power spike, which means the IPC will need to relearn default settings, or therecould be an underlying problem. Technician will need to hook it up to a computer to analyze problem,and relearn settings.

2006 Chevrolet... | Answered on Nov 14, 2019

2 Answers

Solutions for dtc co561

DTC C0561
The electronic brake control module (EBCM) disables the traction control when other electronic control modules set DTCs for components that effect the operation of the traction control system.
DTC C0561 System Disabled Information Stored
Conditions for Setting the DTC
The powertrain control module (PCM) or body control module (BCM) diagnoses a condition preventing the engine control portion of the traction control function and sends a serial data message to the EBCM indicating that torque reduction is not allowed. The PCM or BCM will typically set a DTC and the EBCM will set this DTC.
This vehicle has DTCs which include DTC Symptoms. For more information on DTC Symptoms, refer to DTC Symptom Description .

DTC Symptom

DTC Symptom Descriptor
71
Invalid Serial Data Received
72
Alive Counter Incorrect/Not Updated

Diagnostic Aids
This DTC is for information only. As an aid to the technician, this DTC indicates that there are no problems in the ABS/traction control system (TCS).
© 2015 General Motors Corporation. All rights reserved.
This is something you'll need to take to the dealer !

2006 Chevrolet... | Answered on May 14, 2019

1 Answer

What is the ft. lbs. on a chevorlet 2006 3.9 l impala

Foot lbs for which bolt?

2006 Chevrolet... | Answered on Mar 11, 2019

1 Answer

Cigarette lighters do not work in 2006 chevy impala, have replaced fuses

replace the lighter the coil's burned out that or the socket go to your local junk yard

2006 Chevrolet... | Answered on Feb 13, 2019

1 Answer

How do you adjust headlights on a 2006 Chevy lmala

hi,
you should take it to a shop that has the alignment tool, any other way will not adjust right and you will end up there anyway.

2006 Chevrolet... | Answered on Jan 19, 2019

1 Answer

Were is the crankshaft sensor located on a 2006 impala SS 5.3 Liter V8

REAR RIGHT SIDE OF ENGINE DOWN IN THE BLOCK ....OR AT END OF CRANKSHAFT BEHIND HARMONIC BALANCER THREE WIRES SENSOR -- BLUE WITH WHITE---YELLOW WITH BLACK----LIGHT GREEN

2006 Chevrolet... | Answered on Nov 15, 2018

1 Answer

Where and how many o2 sensors on a 2007 chevy

hi were are 02 sensors locate at I have Chevy impala 2006 3.5 LS i know it have 3 of them I can't find the front one can u let me k ow it is please thank u

2006 Chevrolet... | Answered on Oct 02, 2018

2 Answers

Knocking sound from wheel well

it sounds like you have a bad cv axle on the drivers side.

2006 Chevrolet... | Answered on Sep 29, 2018

0 Answers

Replace rear struts 2006 Chevy Impala

2006 Chevrolet... | Posted on Jul 31, 2018 | Be the first to answer

1 Answer

SPECIAL TOOLS NEEDED TO INSTALL A NEW REAR WHEEL BEARING ON A 2006 CHEVY IMPALA LTZ WITH ABS ?

none really, metric wrenches or sockets, a breaker bar, w jack and jack stands, flat blade screw driver, and a pair of needle nose pliers, to remove the drum holder to get at the wheel bearing assembly.
remove tire then locking washers, remove rotor, using breaker bar, loosen bolt then remove the abs pick up, it is a 10 mm socket, put out of the way, and then remove the bolts, you might have to use a hammer to get wheel bearing to come free from housing.

reverse the procedure to install

2006 Chevrolet... | Answered on Jun 06, 2018

2 Answers

WHAT IF ANY SPECIAL TOOLS ARE NEEDED TO REPLACE A REAR WHEEL BEARING ?

No.
The most you'll need is a big hammer or a air hammer to loosen the bearing from the spindle but just like changing a front bearing

2006 Chevrolet... | Answered on Jun 06, 2018

1 Answer

My ac on my 06 chevy impala clicks on and off could it be over charged

Does the air blow cold? Sounds more like a sign of undercharged. Putting gauges on it would be the best step.

2006 Chevrolet... | Answered on Jun 02, 2018

1 Answer

What size are the two front axle nuts on a 2006 Impala LT 3.9?

Rockauto on the internet, I looked up spindle nut, it showed 34 mm.
I can't guarantee that is correct. Hopefully the autostore isn't too far away so if you get the wrong size socket just take it back and switch it.
In the past, I was changing out halfshaft on different vehicle, bought a new socket for old spindle nut. Turns out the spindle nut on the new/rebuilt halfshaft was a different size, I was not happy.

2006 Chevrolet... | Answered on May 03, 2018

0 Answers

How do you replace the ignition coil on a 2006 Impala 3.9?

2006 Chevrolet... | Posted on Apr 24, 2018 | Be the first to answer

1 Answer

2006 chevy impala battery dead

I drove Volvos for 17 years. Finally learned that a New battery had a short. Meanwhile, I'd changed out alternators. Switched it to a generator. It was a bad battery, from the get go. Just a thought.

2006 Chevrolet... | Answered on Mar 04, 2018

1 Answer

Where is the MAP sensor located on a 2006 Impala 3.9?

2006 Chevrolet... | Answered on Mar 03, 2018

1 Answer

2006 Impala horn sticking on

sounds like relay...check underhood fuse box and replace relay.

2006 Chevrolet... | Answered on Feb 18, 2018

1 Answer

When I hit a bump the heater stop for a few seconds

Are you saying the blower motor stops working? That might be a sign of bad brushes in the blower motor? If that is the case, replace the blower motor. You could check the wiring connector for blower motor.
In the past, I have taken faulty blower motor apart, and those little brushes were wore down to the nub. A bump can cause the brushes to make better contact, or lose contact in your case.
Could be other issues, the blower motor needs voltage and ground. Just my opinion.

2006 Chevrolet... | Answered on Feb 17, 2018

1 Answer