2002 Toyota Camry Solara - Page 2 - Answered Questions & Fixed issues

How pathetic what do you expect in 50C wonder it didnt cook itself to death running a engine in 50 degrees celtigrade ambiante air temperature

Standard size is 205/65R15.Optional size is 205/60R16.205/55R16 may not be close enough but a tire store should be able to tell you for sure. You would have to have the optional 16in wheels already on the car.

Sir, you can have a try of hidhttp://www.chinasinoy.com/wholesale/auto-hid-xenon-light/

have it checked either at a local shop or dealer my scan tool reads in minutes and depending on problem how long to repair. i scan a lot of cars for free at our dealership.

try and tap on the end of the ignition cylinder housing

Try this

Engine stalling and rough run issue at low speeds

This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control

The firing order is 123456. Cylinders 135 are in the rear bank from passenger to driver side. And 246 are in the front bank from passenger to driver side. http://autorepair.about.com/library/firing_orders/bl-fo-1937.htm

This code is usually stored when there is a catalytic converter failure, the cat converter which is part of the exhaust manifold will most likely need to be replaced.

it sounds like there is a problem with the idle control valve and it is located on the bottom side of the throttle body and to help you find it it has three hoses going to it 2 small coolant hoses,1 vac. hose,and 1electrical connector......does the idle ever go down to a normal or lower rpm and also if you have the a/c switch on it will have a much higher rpm.....give me more info and detail so i can help resolve this issue......let me and fixya know if i am doing my job and a thumbs up and a comment would be greatly appreciated......thanks and good luck and have a blessed day......be toyota and lexus tech for over 20 years but need more info so i can try to help you.......

the recliner is part of the framework f the seat. An automotive trim shop may have a far less $$$ solution or look for a used seat at a wrecking yard

Will it idol? Used to reset some by letting them idol for a couple of minutes.

this could be a short, or something simpler to find is the brake light switch, usually located under the brake pedal assembly

Dear,

the brake light switch situated near the brake pedal has gone jammed,
please get the switch replaced.

thanx

Im thinking less causes it sound so dramatic but good thing is you got it started right up, You sound like a sparkplug blew out. This is repairable to and extent of who you take it to, there are kit to rethread sparkplug and use a rethread kit. Hope you get the right people to the right thing

i believe with the trunk open,move the trunk liner out of the way(sometimes held with plastic wing nuts)behind this you should see more wing nuts.remove these and the tail light assembly should pull out to give you access to the bulb sockets to replace them.

pull the door panel off and look for something loose runnig from the hande back to the latch

There's a short circuit within your electrical wiring. Take it to a Electrician now, or else, you're battery will run out of juice !
=)

does the radio work or is it just the cd function if radio doesnt work you may need to take it to dealer for coding but if only the cd isnt working you may have a jammed cd

they are blown... replace them or disconnect them. you had the radio too loud and it broke the speaker,

There will be a 'spring loaded" pulley. There should be a square slot in it or a protruding bolt that you attach a socket with a long handle or a "breaker bar' to and rotate it. You have to hold it there while you put the belt on. Once the belt is on the right way, just release the pulley and it will hold the proper tension on the belt for you.