Yamaha Recent Questions, Troubleshooting Help & Support

Question edited for a lot more clarity, add maker. Question moved to Yamaha Motorcycle. Unlikely to be a carburetor problem as this appears to be fuel injected! https://www.google.com/search?q=Yamaha+Mio+125+MX+no+start ..

Make sure the fuel is getting to the valve and passing through it. Possible blockage in fuel line or in the tank.

I would contct Yamaha for a list of repair agents in your country.

Follow the procedure as given in following link. RX-V6A ' ENJOYING IN MULTIPLE ROOMS (ZONES) (yamaha.com)

It isn't called a Magneto, that was for really old bikes. It is a 'stator'. Service manual https://drive.google.com/drive/folders/1OFbBW2YhLpL1-Xbsw9vexi84Y7aXGTdG Parts List https://www.cmsnl.com/yamaha-rt100-1990-l-usa_model9624/partslist/ https://www.google.com/search?q=1990+yamaha+rt100+wiring+diagram ..

There is an adapter available if you look on computer sites for product purchases, try to google it as there or companies than make such items, might be harder to find as PCI and ISA are older connectors and even AGP is begin phased out an PCI express is the lading connector. Google ISA to PCI adapter and see what you can get your compangies to pruchases from. Your local computer hardware shop might have it call first and ask before driving out there, If you find nothing try calling Tigerdirect as they might have older stock, you never know, If to no avail you will have to try and locate an older Motherboard with the two conncectors on it and run that if possible, or find this certain ISA card you're talking about in PCI. Good luck! :)

Based on the information provided, it seems that the CD player is not compatible with the HDMI input on the Yamaha RX-V372 receiver. This is likely due to the fact that the CD player does not have an HDMI output. In order to play the CD player through the receiver, you will need to use analog RCA cables. Make sure that you have connected the RCA cables to the correct inputs on both the CD player and the receiver. The CD player should be connected to one of the analog audio inputs on the receiver, such as "CD" or "Aux". Once you have connected the cables, select the appropriate input on the receiver using the input selector knob or button. It is also possible that there may be an issue with either the CD player or the receiver. If you continue to experience problems, try testing each component separately to determine where the issue lies. In summary, if your CD player does not have an HDMI output, you will need to use analog RCA cables to connect it to your Yamaha RX-V372 receiver. Make sure that you have connected the cables correctly and selected the appropriate input on the receiver.

Question edited for clarity, full make model (what it is)'. Question moved to Yamaha Audio. It may be sympathetic vibration and is coming from something nearby. Put it on a folded towel or sit in the floor to test it. https://www.google.com/search?q=YST-FSW050+bad+vibration ..

Check your fuel lines and filters. If these are dirty then maybe the fuel is restricted so when you rest the bike the carbs will refill.

You must repair the amplifier first. Take it to an authorised Yamaha service centre.

First make sure that the new battery has been fully charged and is not defective. Next make sure that the proper voltage is reaching the started. You may have a bad post connection or loose connection at the starter. Try jumping you battery with another known good battery.

Question edited for clarity. Question moved to model category. We also have 3 years for it. Ideas here https://www.google.com/search?q=Yamaha+Fazer+1000+hazard+flashers+won%27t+cancel ..

torque specs

Yamaha Blaster Forum https://www.blasterforum.com > ... > Engine Nov 26, 2010 - i think it is 20 lbs, here is a link to a downloadable manual.... http://www.blasterforum.com/general-support-17/downloadable-yamaha-blaster- ... Fly wheel to crank nut torque spec? Jan 21, 2017 Bolt and Torque Specs Mar 6, 2012 Bottom end case bolt torque spec? Feb 17, 2017 Blaster cylinder torque specs..? Feb 1, 2010 More results from www.blasterforum.com

blaster torque specs

Blue Traxx Forum https://www.bluetraxx.com > threads > blaster-torque-s... Dec 25, 2003 - I've seen guys torque things down with a simple ratchet and say how many ft-lbs it is and be within a few lbs. Don't put the kid down for doing ... ..

You might have an internal fuse blown. If you are capable, open up the keyboard and visually look at the fuses. If one is blown, replace with the same amp rating. Good luck!

I had the same thing happen and still can't figure it out

Above the master cylinder on each brake.

Your Service Manual is here

service-manual-yzf-r15.pdf

Ridertua https://ridertua.files.wordpress.com > 2011/04 > se... To help identify parts and clarify procedure steps, there are exploded diagrams "3" at the start of each removal and disassembly section. • Numbers "4" are ... 338 pages ..

If you remove all of the 'unnecessary' sensors, good luck trying to get the engine to run properly as the ECU will be lost and emmision control will no longer work causing the money light to be on permanently.

Question edited for clarity. Question moved to model category. About 2 to 2 1/2 turns out from GENTLY seated. Don't forget this is only idle and low speed air / fuel mixture. 2007 Yamaha Road Star 1700cc https://www.google.com/search?q=2007+Yamaha+Road+Star+1700cc+How+many+turn+out+on+air%2Ffuel+mixture+screw ..

Ok I have same showing on my dash