Yamaha Logo

Yamaha Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 4K Products
  • 158K Answers
  • 3M Views

Hi, Victor no it is not normal and the usual suspects are:
1. Damaged or restricted fuel tank venting system.
2. Loose float bowl screws.
3. Damaged float bowl o-ring.
4. improper fuel level in the float bowl.
5. Worn or dirty inlet valve or seat.
6. Damaged or leaking float assembly.
7. Particle contamination in inlet fitting cavity.
8. Damaged petcock diaphragm allowing fuel to flow through the vacuum line into the combustion chamber.
9. Contaminated fuel tank.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://thumpertalk.com/forums/topic/1075692-ttr-125-carb-overflow-leaking-gas
https://www.ar15.com/forums/general/TTR125_dirtbike_leaking_gas_from_carburator_overflow_tube_/134-1372545
YAMAHA TT R125 Owner Service Manual
https://www.partsfish.com/page/oem-parts-for-yamaha
http://mybikemanuals.com/yamaha/yamaha-tt-owners-manuals

2006 Yamaha TTR... | Answered Yesterday


only if they arent taken care of and lubed

Yamaha... | Answered 2 days ago


Hi, Michael for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.r6-forum.com/forums/57-garage-mechanical-help/135344-yamaha-r6-2008-error-code-20-a.html
Yamaha Fault Codes
Yamaha YZF R6T Supplementary Service Manual
https://www.partsfish.com/page/oem-parts-for-yamaha
https://www.manualslib.com/manual/196057/Yamaha-Yzf-R6t-C.html

Yamaha... | Answered on Feb 15, 2019


Hi, Richard for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Yamaha, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.yamahastarbolt.com/frequently-asked-questions/battery-removal/?PHPSESSID=df376de50fe86356ecbf03bcc7e35187
https://www.yamahastarbolt.com/technical-discussion/best-replacement-battery
https://servicemanualwarehouse.com/yamaha-2016-bolt-r-spec-service-manual/?gclid=EAIaIQobChMI4fa0nKK-4AIVRkOGCh0AvgIUEAQYASABEgKkofD_BwE $15
https://www.partsfish.com/page/oem-parts-for-yamaha
https://www.manualslib.com/manual/1305657/Yamaha-Bolt-Xvs95ch.html

2016 Yamaha Bolt... | Answered on Feb 15, 2019


CHECK WITH YAMAHA IF THEY CAN NOT HELP WE HAVE NO IDEA WHO MIGHT

Yamaha... | Answered on Feb 15, 2019


Right front of the engine is the dip stick. Check for online manuals. Manuals lib is free.

Yamaha MT-03... | Answered on Feb 14, 2019


If the battery is ok then I'd guess it may be the starter relay or fuse that 'popped'. Good luck!

Yamaha 2005... | Answered on Feb 13, 2019


Look very closely at each capacitor to see if any has a burned look or if any shows signs of swelling. If any show these signs they probably need replaced. You should note exactly how you remove a capacitor from the circuit. To test them effectively they need removed from the circuit board. There are several different types of capacitors. If any look like a small can, this will be a canister type and most likely will be what is called polarized. These should have a line running down the side and will have a negative ( - ) sign on them. This capacitor must be replaced exactly the way they were taken out of the circuit with the neg line in the correct place. They must also be replaced with the correct size and value. The number of the value will be on the side followed with what looks like a U with an extra line on the left side. This will be the microfared value. An example is 1000uf. Also listed will be the max voltage the cap can carry, example 250v. The other types of capacitors are ceramic. They can be put back into the circuit either direction. The most important thing to remember is to replace with the correct microfared value, the correct voltage listed and the correct size. Before you start removing any electronic component from the circuit, turn the circuit board over and examine the solder joints. Each joint should be smooth and shiny. If you find one that has pits in the solder then you may have what is called a cold splice. This type of joint may be heating up during operation and the solder melting away from the wire on the capacitor and may run back to the wire after the power is removed, causing a small amount of contact until it is heated again, then the cycle repeat's self. If you find any joint that remotely looks like a cold splice, reheat them with a solder pen and recheck your device, you may have corrected the problem. It is kinda rare for capacitors to go bad but sometimes they do. I hope this helps you.

Yamaha DSP-AX1... | Answered on Feb 12, 2019


Hi, Joanne the answer to this question is way above my pay grade for this situation, I would call or visit my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.bikedekho.com/advisory/how-to-fix-a-stuck-ignition-switch.htm
https://repairpal.com/symptoms/car-key-wont-turn
https://www.manualslib.com/manual/796749/Yamaha-T135se.html#product-Sniper
https://www.partsfish.com/page/oem-parts-for-yamaha
https://www.scoop.it/topic/wvegqux/p/4099263288/2018/07/11/yamaha-sniper-150-manual

Yamaha... | Answered on Feb 12, 2019


Hi, Peter for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.xjrider.com/viewtopic.php?t=437
https://www.louis.eu/rund-ums-motorrad/bike-datenbank/yamaha-xj-600-s-n-diversion/rj01/0869
https://www.manualslib.com/manual/1053640/Yamaha-Xj600s-1992.html
https://www.partsfish.com/page/oem-parts-for-yamaha
https://www.manualslib.com/manual/659436/Yamaha-Diversion-Xj600n.html#product-Diversion%20XJ600S

1995 Yamaha XJ... | Answered on Feb 12, 2019


Hi, Ron the answer to this question is way above my pay grade for this situation, I would call or visit my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://ourpastimes.com/identify-yamaha-its-engine-numbers-7517857.html
https://thumpertalk.com/forums/topic/1122349-help-decoding-my-engine-serial-number/
https://www.doityourself.com/stry/how-to-decode-motorcycle-engine-serial-numbers
http://oem-cycle.com/BikeIdentification.shtml

Yamaha... | Answered on Feb 12, 2019


why do you think you should replace the rotor?
that is a parking brake and is not used to stop
but however if you do this is a big Job best I remember

Yamaha 2005... | Answered on Feb 12, 2019


Hi, Janet for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.starbikeforums.com/forums/18-engine-work/5434-clunking-noise-when-shut-off.html
http://www.ymhmotoboard.com/topic/clunk-on-shutoff
https://www.manualslib.com/manual/833178/Yamaha-Xvs650.html
https://www.partsfish.com/page/oem-parts-for-yamaha
https://www.manualslib.com/manual/833178/Yamaha-Xvs650.html

2006 Yamaha V... | Answered on Feb 12, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Popular Products

Top Yamaha Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5809 Answers

Marvin
Marvin

Level 3 Expert

83951 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22441 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...