Pride Health & Beauty - Page 4 - Recent Questions, Troubleshooting & Support

Hi
The Jazzy 1103 PDF document contains a lot of the electrical diagrams I've got it if you send your email address i'll send it 2 u. put the word at in place of the @ that will stop you getting sent spam

Tony

A bit of repair work is required now as the seat will not lift off without firstly lifting the lever.

Fit the lever back on first.

Re-check you have removed all of the screws as they sometimes have a extra ones positioned in a hidden and difficult places to get at or you need to remove another trim piece to release the panel you want to take off, possibly the knee panels on the tiller bar. The pot and key barrel will be mounted to the trim panel directly so won't be holding the trim down. The trim panel itself may be held in place with moulded clips so you may need to GENTLY lever along the seam between the panels to 'Pop' the panel loose. Most scooters of that type have a speed pot that is held in place with a small nut. The plastic 'button' you twist to alter the speed setting is a 'push on' cover. It will be a tight fit but it should simply pull straight up and off revealing the small nut holding the pot in place.

flashing green means it is 80% charged and will change to solid green when fully charged. Basically telling you that you can go for a quick spin if you wish. https://www.pridemobility.com/pdf/troubleshooting/infinfb2586_charger_led_indications.pdf ..

Try a local auto transmission rebuild company. Or, here for your parts https://www.google.com/search?q=pride+DRVASMB1627 Motor transaxle and brake is here https://www.monsterscooterparts.com/brands/pride/models/legend-xl/motor-assembly-motor-transaxle-and-brake-for-the-pride-legend-xl-sc3450.html More here https://www.google.com/search?q=pride+DRVASMB1610 ..

Hi Ricky. It helps to have make and model in all questions. This place sells used ones for $20 upwards depending on make. https://www.wheeliegoodmobility.com/used-mobility-scooter-speed-potentiometers.html Lots more here https://www.google.com/search?q=mobility+scooter+potentiometer+control ..

Hi, the correct info is found the following link , http://www.pride-mobility.co.uk/docs/GO-GO%20Elite%20Traveller%20Plus%20owner%20manual.pdf Regards Rob www.gewizrepairs.co.uk

You say it still had a binding feeling in neutral ... check the wheel bearings and output shafts.

There is a YouTube video of a guy who got one to do 70 mph! Basically, you just need the battery, a potentiometer and the motors. I reckon a floor mounted sewing machine foot pedal would work! People have already worked out how to do it. https://www.google.com/search?q=pride+mobility+scooter+speed+limiter+removal Thanks for the kind comments :>D ..

Unfortunately, NOT using them is worse than using them all the time. Using it, might free it up. Find a big empty car park and do Start - Stop - Start, flat out runs for 30 minutes. This is a common problem often caused by the potentiometer (pot) in the centre of the Wigwag (Accelerator.) This part takes a lot of "abuse" and the pot causes an intermittent electrical connection resulting in a very jerky ride. Try spraying a contact cleaner spray in the pot but most often the potentiometer will need to be replaced by a technician. https://www.pridemobility.com/go-go-travel-mobility/go-go-elite-traveller-4-wheel/

The kids in the shop were probably racing it. Just take it back. Makes sure both batteries are charged and the terminals are clean and tight.

Your scooter needs a new battery then and needs to be replaced.

Question edited for clarity. Question moved form Car Audio to Pride Jazzy Select 6. 9 Flashes The park brakes have a bad connection. Check the left and right motor connections and wiring. Check to make sure that the power chair is not in freewheel mode.

jazzy select - Any electromechanical device requires ...

Videos as well https://www.google.com/search?q=jazzy+select+6+blinks+9+times& ..

a cheep fix is the charger I am showing you from Advance auto it will bolt into stock location and bolt to battery post you will need to make a jumper wire to send batt. voltage to joy stick controller well worth doing the modification to save big $$$$.

Question edited for clarity and punctuation. Question moved from Cars and Trucks to Pride Legend. If it is inside the motor is is likely to be bearings. You would need to remove the motor, test it out of the scooter and see if it still make the noise. If it does, then it need a full disassembly to find out what is worn? My view is that is more likely to be the brake rubbing, or a stick/leaf stuck behind the wheel.

Question edited for clarity. Check out the video. https://www.google.com/search?q=remove+the+seat+on+a+pride+celebrity or Page 35 of your manual. https://www.pridemobility.com/pdf/owners_manuals/intl_scooter/canada/english_pdf/ca_celebrity_x_om_e.pdf ..

You manual merely says this on Page 26 Make sure the seat is locked in position. Lift the seat off. https://manualzz.com/doc/8931129/pride-legend-owner-s-manual There are some videos for Pride Scooters here https://www.google.com/search?q=Pride+Legend+remove+seat ..

Take it in for service. It sounds like it has been modified or something is stuck in the motor fans. We are Fixya, we aren't the maker of your unstated make and model scooter. I moved the question for one of our mobility scooter Categories, purely as a guess!

This sounds like it is trying to "Short Out". Turn off all the power to the chair and re-check your battery connections. A "Short" is where the electricity is trying to flow the Wrong way around the circuit. This will badly Damage you batteries if you keep trying to connect them. When connecting batteries together you ALWAYS connect a Positive (+) to a Negative (-). NEVER Positive to Positive or Negative to Negative. Start at the Negative wire, connect it to the Negative terminal on the first battery, (Battery One). Then on Battery One connect the Positive terminal to the Negative terminal on Battery Two. You now connect the chair's Positive cable to the Positive terminal on Battery Two. You should get NO sparks. Carefully turn on the chair's power. The batteries should NOT spark and should NOT get hot quickly. **CAUTION** If it does spark or get hot quickly after you have done this TURN EVERYTHING OFF and disconnect the negative cable. This means there is a problem somewhere else in the chairs electrics.