Powermatic Logo

Powermatic Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 119 Products
  • 203 Answers
  • 40K Views

you are loading way too tightly, do not force when pushing the handle down, if you have too you are over packing. I have loaded 200 cartons of cigs on these machines and never broken a thing

Powermatic 2... | Answered on Jan 15, 2019


I called them or
pic your part here then call
http://www.powermaticinjector.com/c2instruct.asp

Powermatic 2... | Answered on Jan 15, 2019


Maybe the manufacturer on their website .

Powermatic 2... | Answered on Jul 21, 2018


That's right, if it is within it's warranty period, return it. On the other hand if it is out of warranty and you are somewhat mechanically inclined, you can open it up. The screws are in the bottom of the unit under the feet. Take them out, open it up and you will see there are connector(s) on the circuit board you see 1st. Unplug the connectors, clean things up as you go also. Do take note of the orientation of the connectors. Once that board is out, you will see another smaller one under it, and the motor w/mechanical parts attached. The small circuit board is the optic that senses the position, likely has tobacco dust obstructing it. Either remove it and dust it off, or use some canned air and blow things out. While in that far, check the mechanical parts for wear, they should not be too loose. There is play in them, but not sloppy. Hope that helps :)

Powermatic 2... | Answered on Jul 16, 2018


The Powermatic 1791264k Model 719T Tilt Table Mortising machine, works excellent and it is a very good equipment. I have no regret in purchasing this machine.
More details Make elegant choice with Powermatic 719T Mortiser Review

Powermatic... | Answered on Apr 09, 2018


Powermatic is the great drill press. If you need any information about the Powermatic drill press go to the link Make elegant choice with Powermatic 719T Mortiser Review

Powermatic 1140... | Answered on Mar 29, 2018


If you want to see Powermatic drill press review go to the link Make elegant choice with Powermatic 719T Mortiser Review

Powermatic... | Answered on Mar 21, 2018


I am going to go under the assumption you are using 100mm tubes. I just switched to kings to make life easier but here is how I filled my 100mm to the filter with good compaction and a trick to get it to the filter. I tightly pack the tobacco against the left side, sticking my finger in the chamber and pushing pretty hard to compact to the left side, I then just do a light poke for the rest of the compartment. Here is the trick part, take a finger and put light pressure pushing on the filter towards the machine, but not so hard it bends the tube and also no so hard that when the injector probe comes out it pushes your finger away from the machine. Using this method I would get around 9 good packs with one redo out of 10 injections. The key is to have enough pressure to hold the filter at the point where the plastic tab usually pushes out and then let the probe push your finger away from the machine. Only very light pressure is needed to make the difference. If the cigarettes are not packing tight you are not compacting enough tobacco in the chamber. There is a fine line though, you need to find the balance as stuffing too much in will cause it to bind up, you just need to find the balance. Once you figure it out it will go very quick, I stuff mine while on the phone and can do around a pack every 2 to 3 minutes or so and get a cigarette that can not be distinguished from a store bought one.

Another tip: I use old cigarette packs as containers for my DIY smokes, you can do the same here with a plastic case. If I do get some that are not fully pushed against the filter using the above method, or if the pack just seems a little loos I put them aside and at the end I load them all in cigarette packs just like they come from the store, filter up (otherwise I have a habit of smoking filters from years of them being positioned this way!) and once the pack is full (add good ones if there is space for them to move around, it will not hurt them) turn the pack upside down so the lid is on the bottom. Now tap them firmly about 10 to 20 times against a hard flat surface. This will move the tobacco towards the filter if there is a space or pack loose cigarettes.

Warning: From my experience :) Do not over stuff the machine or using the compacting method do not over pack the tobacco, find a good medium. If you over pack the smokes will be solid and very hard to drag from. Do not smoke cigarettes that are hard to rag from, the extra force needed by your lungs followed by introducing smoke into your lungs will result in pain and maybe worse, but I only made that mistake once.

Good luck!

Powermatic 2... | Answered on Jan 09, 2018


There should be some screws on the bottom side of the fence that allow you to make adjustments. Loosen then slightly then set the fence to 90 degrees & then tighten them.

Powermatic... | Answered on Jan 05, 2018


sorry but FIXYA has no idea where they would sell pars if the dealer or manufacturer can not assist

Powermatic Saws | Answered on Dec 21, 2017

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Powermatic Experts

80stech

Level 2 Expert

120 Answers

ray gallant

Level 3 Expert

60369 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2004 Answers

Are you a Powermatic Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...