Jetway Popular Questions, Answers, Tips & Manuals

is it on the right pin for power pins on board

Suggest to test the unit with another power supply if possible. -Possible that power supply my be dead. If not possible then you will have to contact Jetway for a RMA for no power. Ref: http://www.jetwaycomputer.com/TechSupport.html

Hello here is the homepage:http://www.jetway.com.tw/jw/download_show.asp?productid=P4X400DBPI think maybe the graphic card has died.Try to add a new or used AGP graphic cardin the slot on the mainboard.Check also the screen/ or cable on another pc for fault.Good luck

Desktop or Laptop computer ?WARNING: Before you start troubleshooting remember that you are dealing with electricity that can KILL.

http://www.kitchentablecomputers.com/static.php - rules

Test all power and data leads that attach to your hard drive IDE,SATA

the leads from your (motherboard to your hard drive) make sure they have secure dust free connections and are not faulty

if its a 40 pin flat ribbon type it will be the first to fail

make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty

even something as small as a faulty electrical fan and its lead can cause you problems

computers need all power and data to continue through every working device and to have an end so any faulty leads will end up with a computer error

make sure your graphics card is securely seated with no dust built up or in the socket

if you remove your graphics check the socket to make sure its dust free

restart your computer then reinstall it this should activate found new hardware wizard

hope this helps

http://download.cnet.com/2000-20_4.html on the home page you should see a search tab just type in what you are looking for

IE: motherboard name audio driver you might have to try a few times to get it right

hope this helps

Yes provided the expansion slot on the motherboard can fit this graphics card. If your motherboard has a built-in graphics chip then you most likely need to disable the on-board graphics before installing this graphics card and driver..

In Windows? - New drives have to be readied for use. Try Start > Run (aka Search in Win 7) type dskmgmt.msc. Look for your drive there. It should be without a drive letter. Right clicking will give you the options of initializing, creating disc partitions, assigning logical drives, and formatting. If this seems a little daunting. A wizard should load. If not there is refresh icon on the toolbar.

PCI-E graphics cards are the correct interface. Just buy what you can afford.

Open Personalization by clicking the Start button, clicking Control Panel, clicking Appearance and Personalization, and then clicking Personalization.

Click Window Color and Appearance.

Under Window Color and Appearance, click the color you want, and then click OK.

Note

If you see the Appearance Settings dialog box instead of the Window Color and Appearance

window, the theme might not be set to Windows Vista, the color scheme might not be set to Windows Aero, or the computer might not meet the minimum hardware requirements for running Windows Aero. For more information, see Troubleshoot problems with Windows Aero.

hope this helps

I can't get you a copy of that CD but I can tell you where to get all the drivers, Bios, Utilities, and manual from:http://www.jetway.com.tw/jw/download_show.asp?productid=P4MFM#I hope it helps!

you will have to open up your network connections click start control panel network connections this may vary depending on your operating system look for local area connection if you see a red X or a yellow exclamation or question mark ! ? you will need to update or install the driver or it could be firewalled click start control panel administration tools computer management device manager scroll to network adapters should see a yellow question mark? right click install drivers the driver might be on the disc supplied by your ISP internet service provider or the motherboard disc or you might download one if you dont have on a disk

Make sure you Ethernet is enabled in bios restart your computer during the boot up process you will see on your screen a certain key to press to enter set up (BIOS) press and hold that key to enter bios using arrow keys scroll to intergrated peripherals look for SiS On Chip Pci Device press enter scroll to SiS 10/100m press enter make sure its enabled

if still no lucki

click start type cmd press enter you will be in DOS mode

type in ipconfig press enter

you will see all of your internet connection details

or type in your default gateway adress into your internet search should read something like 10.0.0.138 to get an inertnet connectionhope this helps

Replace the memory chip or try it in a different memory slot. Sounds like it has some issues.

Dear,You can download all drivers related with "Jetway I31GM4 Motherboard" from the below mentioned link.http://drivers.softpedia.com/dyn-search.php?search_term=etway+I31GM4-L+&Submit=Search&lastupd_filter=0&results_per_page=20&sort_field=0best of luck!

Dear,Get all of your drivers from this link!http://drivers.softpedia.com/dyn-search.php?search_term=etway+I31GM4-L+&Submit=Search&lastupd_filter=0&results_per_page=20&sort_field=0best of luck!

Whree get driver mainboard jetway I31GM4 - LF ????

Most online computer parts stores sell the part you are looking for. Try putting the part number into your seaarch engine for prices and where you can get one.

Clear CMOS (JBAT)

if the computer will not boot move the jumper the 3 pins to the other side.

I am not sure you have the exact model I do, but the battery is on the underside of the motherboard - you must undo the four silver screws holding the board down, and also two screws to remove the front plate. Pull the board up and out, and you will see the battery underneath.

One bad lead can cause a computer to continue on a cycle or to shutdown or fail to detect your hard drive boot up

test all leads that attach to your hard drive including electrical extensions SATA

the leads from your ((motherboard to your hard drive)) make sure they have a secure connection and are not faulty or just replace them they could be faulty make sure all leads that are attached to your drives dvd\cd have secure connections and are not faulty or just replace them they could be faulty ?

even something as small as an electrical extension or a faulty fan lead can cause this problem computer needs all of the data and power to travel through every working device and to have an end for a computer to be able work properly

a motherboard and a hard drive any leads between them will fail before your motherboard or your hard drive check all electrical extensions make sure they are securely seated even the cd/dvd drives need to have current go through make sure these devices are working

also check your computer ram modules and cmos battery to make sure they are securely seated and the battery has plenty of charge Cmos battery on some motherboards are soldered in hope this helps you

After a fresh install of an operating system you have to set up your sound again if your computer came with a motherboard disc the sound drivers could be on it click start control panel administrive tools computer management device manager scroll to sound,video and game controllers you might see a yellow question exclamation mark? ! or a red X Right click to reinstall drivers click start control panel sounds and audio,volume,advanced,speakers make sure you have selected the (((appropriate speakers))) also audio you will find 3 drop down lists make sure you have the correct settings there also click start control panel sounds and audio devices select advanced there might be a tick in the mute box untick it if his does not fix the problem click start control panel sounds and audio devices you can adjust the volume there also select speaker volume you can change your settings there you can also tick in the box place icon in taskbar for any further volume control settings you will need to right click on the volume icon system select adjust volume

click start control panel sounds and audio,volume,advanced,speakers select the appropriate speakers from the drop down list or navigate to the device manager scroll to system devices + to expand,system speaker right click properties then select use this device (enable) also you might check the speakers plug/outlet is usually at the back of the computer you will have to open up the computer to check the lead attached to the rear of the input plug make sure the connection is good try cleaning your computer of dust using a fine air blower from a compressor making VERY sure that there is no MOISTURE in the air line specifically around the sound card and the CPU central processing unit dust causes static to build up in a computer hope this helps you