Jado Popular Questions, Answers, Tips & Manuals

Do you work here? Claim your company

  • 97 Products
  • 30 Answers
  • 7K Views

WHAT IS QUESTION ? we do know answers to unknown problem.

Jado Plumbing | 79 views | 0 helpful votes


Fixya is unable to source parts.

Jado Plumbing | 353 views | 0 helpful votes


If you do not have an expansion tube on your hot water heater that might help.

Jado Home | 74 views | 0 helpful votes


Use a block of wood and a couple flat head screwdrivers
carefully pry up on the faucet handles using the wood as leverage. But do not force them, heat up with a hair drier first before removing.

Jado Plumbing | 162 views | 0 helpful votes


faulty cut off to faucet , calcium ,'

Jado 827-850-144... | 94 views | 0 helpful votes


you need to remove handle and the nut from the TOP . put it back in place then start over

Jado Plumbing | 247 views | 0 helpful votes


vinegar and old toothbrush to work it in the threads. let sit for a few minutes. repeat.
keep trying gently.
try tightening it a TINY bit before unscrewing.
vise-grips with rag wrapped around.

Jado Plumbing | 85 views | 0 helpful votes


It will require two people one to hold from top and underneath using deep socket remove nut.

Jado Plumbing | 102 views | 1 helpful votes


Is this a new or used faucet

Jado 827-850-144... | 141 views | 1 helpful votes


cartridges are one piece unless
cartridges replace the insert and tap washer

Jado Plumbing | 195 views | 0 helpful votes


Is it a star socket maybe?

Jado Plumbing | 517 views | 1 helpful votes


if it was new,it was defective or installed improperly

Jado 842/404/144... | 351 views | 0 helpful votes


Depends on the type of handle. If you have both hoe and cold handles they can usually be removed by prying off the cap that has "C" or "H" on it. Under that there will be a Phillips screw.
Single handle have hex key set screws on the back or under side. Use can back that out with an "Allen" wrench.

Jado 842803100... | 226 views | 0 helpful votes


DUH that means a 1 inch hole for the middle and a 3/8 for the side holes not 1 3/8 to begin with

Jado Plumbing | 125 views | 0 helpful votes


Sounds like you installed the cartridge incorrectly. The orientation is important to note when removing the old unit. Try pulling it out and reversing the orientation. Check the inlets and match them up.

Jado Plumbing | 266 views | 0 helpful votes


www.jadousa.com

Jado Model... | 409 views | 0 helpful votes


I am providing the link of the installation instruction for your reference. It seems that there is a lock nut underneath to hold the faucet (figure 1, part 6). http://www.jadousa.com/assets/documents/jado/install/Install_3874.pdf

Jado 842/701/105... | 145 views | 0 helpful votes


The specs say that there are two check valves but the diagram does not show them. Take the weight off the hose and see if it is causing the restriction. If it is not, what is the water pressure in the house? The 2.2 GPM is the maximum flow rate.

Jado 803800355... | 197 views | 1 helpful votes


On the cartidge there should be a little stopper on the stem that sticks out where the handle goes on ( this prevents the handle from going all the way up ) try repositioning this stopper. good luck

Jado Shower... | 148 views | 0 helpful votes

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Jado Experts

Brad Brown

Level 3 Expert

18031 Answers

Marvin
Marvin

Level 3 Expert

84565 Answers

ray gallant
ray gallant

Level 3 Expert

62053 Answers

Are you a Jado Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...