I print to a printer connected to the company network. I started to print a 40-page document, but realized immediately that the document needed one more change, so i cancelled the print job. After making the change and printing the document again, i walked to the printer and found the printer printing many pages with unrecognizable characters. What might be worng? please help!!

Your printer driver is corrupt. Go to Canon's web site to get another download. Uninstall the old printer driver before installing the new driver or it won't work.

Hi there, it sounds like your saying you have a network printer that you set up and it was able to print a test page during setup or at the end of it but are unable to print a pdf or word document. If you have multiple printers installed or if you have this printer installed on network as well as physical usb connection with the computer, take care to be sure you select the network port to the printer. In other words in the print dialog when you select you printer it should say "network" next to it or something simular not local or usb or even just the plain printer name, it should reference to the fact it's the networked connection. There could also be other things but start there and let me know if that works.

Good luck and thanks.
Questions? Just ask! Mr.Mike

When you installed your printer, you had to install the software on your PC. So go to your PC's start menu, go to Programs, select Lexmark software, select Tools and then select Wifi Configuration Utility. It will open a window which will give you step by step instruction on re-configuring your wifi settings. When you are doing this, make sure your printer is connected to your PC via the USB cable.

Well sometimes you can restart the printer...also you can start printing where it left off if you see what page it was and then hit print and look in window and set start page such as 21-40

Take out the power cable from the printer and then keep the power button pressed for 30 seconds. After that connect the power cable and try to print.

You have to go to Control Panel or TaskBar where you can see your PRINTERS folder. If ther are many printers listed, select your printer.
You have to delete the printing job from the queue.
When there is nothing more in the queue,
Print again, this time go through the menu, and instead printing the whole article specify pages like Pages 22- 40 ( Omit the first pages you have already printed.
Hope this will work for you, have a good day
luciana44

It is more likely the program that you are using than the prnter. Open START ACCESSORIES and NOTEPAD place some text on thios page and send to printer If this prints OK then whatever you are using to create the documents that dont print is the offender. If its a mices all thaduct Can I recommend a freebie that does all that MS does and more.

go to www.openoffice.org and download the program. Its a full working and FREE type of MS office without any high price tag. It writes like MSOffice saves files in office foirmat and reads msoffice files It also behaves better in printing. Even the menu and icons are similar

If you scroll through the menu functions to service, you can restore factory defaults. If you use the fax function you'll need to run the AiO assistant again. It may take care of it. I didn't see anything on the config page or the menu structure page that would indicate an option to require a print report after each document.

Network Configuration page
NOTE The Network Configuration page is only available on the HP LaserJet p2015n,
HP LaserJet p215tn, and HP LaserJet p215nw printers.
A Network Configuration page prints whenever a printer configuration page is printed. You
can also print a Network Configuration page by pressing the network Reset button at the
back of the printer
The Network Configuration page provides information about the network configuration,
including the IP address, firmware revision, network statistics, protocol information, and so
on. The Network Configuration page automatically prints when you print a configuration
page from the control panel.
ENWW Printer information pages 37
Using the HP Toolbox
The HP Toolbox is a Web-based program that you can use for the following tasks:
● Check the printer status.
● Configure the printer settings.
● View troubleshooting information.
● View online documentation.
You can view the HP Toolbox when the printer is directly connected to your computer or
when you are using a supported network connection. You must have performed a complete
software installation to use the HP Toolbox.
NOTE You do not have to have Internet access to open and use the HP Toolbox. However, if you
click a link in the Other Links area, you must have Internet access in order to go to the site
associated with the link. See Other links for more information.
To install the HP Toolbox, you must install the TCP/IP protocol and the most recent version
of the Java™ Virtual Machine on the computer. You must also install the DOT4 protocol for
all USB connections, LPT connections for Windows 2000 and Windows XP, and LPT1
connections for Windows 98 S.E., Windows Me, and Windows NT 4.0. See the system
administrator or computer manufacturer's documentation for more information about
installing the TCP/IP protocol and the DOT4 protocol.

It could be losing connection to the printer when there is too much information to print.  
If the cable the information needs to travel through is too long or the distance to the printer is too far - information is "lost" due to the stability of the connection.  The longer the information needs to travel the more unreliable and unstable it becomes.
Have you tried from a different computer to print the document?