Dell printer will not print. Receiving message: fuser error

Replacing The Main Service Part Of Fuser Unit - Dell 1135N ...

https://www.manualslib.com > ... > Service manual
Dell 1135N Manual Online: Replacing The Main Service Part Of Fuser Unit. 3.6.3.1 Spring-Es Separate it as take up the circle-area of Spring-Es from hook.

How to replace fuser in Dell 1135N printer - Fixya

https://www.fixya.com > support > t24863785-replace_...
Jul 23, 2014 - how to replace fuser in Dell 1135N printer how do you change the fuser - Dell 1135n AllInOne Laser Printer question.
20 Most Recent Dell 1135n AllInOne Laser Printer Questions ...
Nov 18, 2012
While install refil toner in Laser printer Dell 1135n - Fixya
Nov 19, 2019
My 1135n all in one won't recognize my local computer - Fixya
Nov 18, 2019
Dell 1130 Laser Printer 1130 fuser error #02-000 - Fixya
Aug 22, 2012
More results from www.fixya.com

Support for Dell 1135n Multifunction Mono Laser Printer

https://www.dell.com > Support > Product Support
Search Dell 1135n Multifunction Mono Laser Printer Support Information ... Troubleshoot Printer Spooler Errors, and Removing Printers from Windows Registry.

• 
  

  Support for Dell 1135n Multifunction Mono Laser Printer ...

  https://www.dell.com > Support > Product Support
  Search Dell 1135n Multifunction Mono Laser Printer Support Information ... Troubleshoot Printer Spooler Errors, and Removing Printers from Windows Registry.

Replacing the fuser on Dell Laser printers (C2660dn ...

https://www.youtube.com > watch
PREVIEW
1:04 Watch this video to learn how to replace the fuser in your Dell C2660dn, C2665dnf, C3760n/dn and C3765dnf laser printer.
YouTube · Dell Support · Aug 15, 2014

You may need to replace the fuser.

There's not much on the web about this error message, but it does say to reseat the fuser. I found a writeup (with a picture) on how to do this.

http://en.community.dell.com/support-forums/peripherals/f/3528/p/19309114/19606748.aspx

Make sure that your printer is unplugged while you do this, also be aware that the fuser gets quite hot while it's printing and stays hot for a few minutes afterwards. Don't burn yourself! While the fuser is out you may want to blow out the dust from the printer with a can of compressed air.

If reseating the fuser doesn't get rid of the error message call Dell technical support at 1-877-293-1197.

Hope this helps

Please rate this solution, thanks!

Disassemble fuser and inspect thermistor, thermostat and heat lamp. Replace broken part.

I would if it will print I would try a laser printer cleaning kit canbe found at any office supply like office max or staples

please check if the fuser is inserted properly:)

Your fuser is not warming up. You will need a technician to look at it.

Check for damage to the fuser located right were the paper exits. damaged fuser can cause lines

What is the error message you are getting with the new fuser. Is this the same error you were getting before changing the fuser? If you changed the fuser because the old one was just at EOL ( end of life) but did not give you an error, have you tried to reinstall the old fuser.

It is possible that the new fuser was damaged in shipping, or not properly seated.

If both the new and old fuser give the same error message, then yes, I would agree that the LVPS would be the next part to replace, however, if they have different errors, then you probably have 2 bad fusers ( or one that is EOL, and one that was received damaged).

Before changing the LVPS, make sure you follow the steps below prior to the LVPS steps.
as far as where to purchase it if you do in fact need one, you can always do a google and ebay search for "Dell 5100cn LVPS".

I can provide you with replacement instructions if it comes to that.

See below for the actual troubleshooting needed for the fuser.
The following steps are the troubleshooting steps that should be followed for error code 010 397.
First, the definition of the failure is <IOT Fuser Failure>, and means a Fuser Error is detected.

1) With power off, reseat the fuser by physically removing it from the printer, then reinstalling it and locking it in place. Turn the power back on. ( if the error is still present, proceed to step 2 ).

2) If reseating the fuser did not resolve the problem, Replace the fuser with a known good fuser.
( if problem is not resolved, proceed to step 3)

3) Replace the LVPS ( low voltage power supply ). ( if problem not resolved, proceed to step 4 ).

4) Replace the PWBA MCU ( printed wiring board assembly - machine control unit ).

END of troubleshooting.........

920 Fuser Error
Indicates that the fuser is below temperature when printing


Do a Fuser Service Check