Bobbin won't wind correctly!!

If the needle on your Singer Quilter Confidence machine moves when you're winding the bobbin, it's likely due to a few possible reasons. Here are some steps you can take to resolve this issue:

1. Check the threading: Make sure the thread is properly threaded through the machine, as an incorrect threading can cause the needle to move during bobbin winding.
2. Tighten the needle clamp screw: If the needle clamp screw is loose, it can cause the needle to vibrate during bobbin winding. To tighten the screw, use a screwdriver to turn the screw clockwise.
3. Check the bobbin winder tension: If the bobbin winder tension is too loose, it can cause the needle to move. To adjust the tension, refer to the manual for your Singer Quilter Confidence machine.
4. Check for any obstructions: Make sure there are no obstructions near the needle, such as thread tails, fabric, or lint, as these can cause the needle to move during bobbin winding.

If you've tried all of these steps and the needle continues to move during bobbin winding, it may be a mechanical issue that requires a professional to fix. I would recommend contacting Singer for further assistance.

1. Turn the power on the machine.
2. Open the bobbin winder cover at the top on the right side of the sewing machine.
3. Swing up the bobbin thread spool pin. Move the bobbin thread spool pin up as far as possible.

1-Bobbin thread spool pin
4. Place the bobbin on the bobbin winder shaft so that the spring on the shaft fits into the notch in the bobbin.

1-Notch
2-Bobbin winder shaft spring
5. Slide the bobbin winder shaft to the right.

NOTE: If the correct size bobbin is not used at this time; when the bobbin winder is engaged; the bobbin winder will make a usual noise and not wind the bobbin correctly.
6. Place the spool of thread for the bobbin onto the bobbin thread spool pin.
7. Slide the spool cap onto the bobbin thread spool pin.
NOTE: If using thread that winds off quickly, such as nylon or metallic thread, place the spool net over the spool before placing the spool of thread onto the spool pin.
8. Pull out some thread, and then thread the thread guide for the bobbin winding. Hold the thread with both hands, and then securely pass the thread as far as possible into the two slits in the thread guide.

1-Thread guide for bobbin winding
2-Two slits
9. While using your left hand to hold the end of the thread that wraps around the thread guide for bobbin winding, use your right hand to wind the free end of the thread clockwise around the bobbin five or six times.

10. Pull the thread to the right and pass it through the slit in the bobbin winder seat.

I always use my finger to guide the thread as the bobbin is winding,the bobbin shouldn't be moving around in the metalcase probably needs tightened.

Hai, Please change the new bobbin winder. Because bobbin winder and winding is very important.

Check to make sure the thread path from the spool to the bobbin is correct. The thread should make a loop around a little post that is actually a tensioner that helps the thread wind smoothly onto the bobbin. If something is wrong with that tensioner or the thread is not following the correct thread path, it could cause the thread to not wind smoothly. It appears that your machine has two locations where the spool can be placed to wind the bobbin. You might try using the other option, if one doesn't seem to be working.

Also, you might try slowing the machine down during the thread winding process. It it goes too fast the spool begins bouncing and pulls the thread akilter. Also, some threads will stretch if the winding is too fast causing the thread to "shrink" when sewing your garment and creating puckers.

FWIW, I found that a "SideWinder" stand-alone bobbin winder is a handy gadget. It is available for ~$30 from JoAnn's Fabrics, Amazon, etc and is battery or electric compatible. It saves wear and tear on a machine and can wind multiple bobbins one right after another. Just be sure to verify that your bobbins will work on the SideWinder as some Singer bobbins will not.

try changing the needle
rethread the machine top & bobbin
make sure the bobbin is wound correctly & inserted correctly
into the bobbin case
if these suggestions don't help then you might think about having
the machine checked at a sewing machine shop

the thread guide & the bobbin spindle need to be check to see if there
is something wrong or just needs to be adjusted

if the bobbin thread is winding around the bobbin winder spindle then
the bobbin is not sitting correctly on the bobbin winder spindle,,
the bobbin (metal or plastic) should lock in on the bobbin winder spindle
& the the thread should be around the bobbin tension guide

If the fly wheel is going around then the clutch isn't disengaged to wind the bobbin, you need to pull out the flywheel on your model to disengage the clutch for bobbin winding.


Take thread from thread spool across to bobbin winder thread guide, then back to bobbin and thread the tail through the hole on top of the bobbin. Place bobbin onto spindle on top of machine and then push it against the stop to engage the bobbin winding motor. HOld the thread tail up and start winding slowly until the bobbin core has been covered including the starting point. Stop and trim off the thread tail with scissors. COntinue winding bobbin and give the thread a nudge if needed to wind evening top middle and bottom of the bobbin. A good smooth wind is important. Also don't wind at full speed and keep an eye on the thread reel that the thread is coming off, you don't want it bouncing around as this will **** the thread and stretch then relax it affecting your bobbin wind.

Obviously if you know this and the bobbin winding mechanisim is just not working, then it will need a service/replacement by an Elna repair person.

Make certain the bobbin is inserted correctly into the bobbin case. If it is, be certain the bobbin is wound tight. A bad wind will cause the loose threads you mentioned. If both of those options are all right, check your upper tension. Generally, it should be set at 3. Also, make sure the needle is inserted correctly...the groove on the face of the needle should be facing the front of the machine (it is actually a thread guide). And last, has the bobbin case been removed and cleaned? If not, this could lead to "messy bobbin threads." I hope one of these suggestions is THE one for your problem. Good luck!