Question about Yes Televison & Video

Open Question

Yes i am trying to watch tv cable, was working yesterday and now cant input tv from source

On the screen it says no channel is registered

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: tv not working

Can you confirm that you didn't have any input signal? My wife once accidentally pressed the reset button on the remote and the TV was stuck in this state. I tried to hook up an antenna to the digital antenna input and let the TV search for a channel. It did find a station and got out of the channel search mode, which was all I needed. Then, I unhook the antenna and continued to enjoy my DVD movie. I didn't check the manual. So, it's possible that there is a better solution. My TV was working fine and I think it just has a terrible user interface. I'm not sure about your TV's condition, though.

Posted on Sep 19, 2007

Ad
  • 208 Answers

SOURCE: HDTV Sharp- Input select to watch Cable tv

On the sharp remote you will find an input button. You depress the input button and a menu will appear and highlight the input you are presently on. Hit the input button again to select the next input. If you wait to long to depress the input button it will not work and you have to begin again. This unit will only hightlight inputs have a component hooked to that input.

Posted on Feb 05, 2008

ebrus
  • 30 Answers

SOURCE: DS24205 TV INPUT PROBLEM

You can buy an rf modulator ( very cheap) and connect your dvd player, game console etc) to the modulator then connect the modulator to your antenna with a coax cable. This worked for me. It placed the connection to channel 4 and other cable channels are still working,

You can buy the RF Modulator from: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=180299245670

Posted on Oct 17, 2008

salsaurbana
  • 56 Answers

SOURCE: mintex 37 inch wide screen. remote is working however cannot change channel, input source or volum. only turns tv off. The buttone on tv doesnot work connot change input source or volume

Check if the remote is in TV position, that is, because most of the remote controllers have the feature that you can program them for use with another devices. Make shure that one button that says "TV" in pressed and released once before you try to change any function on the TV.

Posted on Nov 20, 2008

rulds2008
  • 3866 Answers

SOURCE: change input source for philips magnavox

use the up/down channel until you get to the input you have connected. You did not say you had a remote so i am using the standard fix for this.

Thanks


Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

Posted on Apr 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I keep getting a blue screen on my Insignia TV. Cable box still shows the channel and I can change channels but nothing on screen. No sound either. This TV is not even 3 years old yet.


A blue screen indicates no video signal, if you change the video input to a DVD player is it still a blue screen? If yes then the TV is defective. If no then some how the signal is being lost to the TV from whatever source you use for watching broadcast TV

Apr 05, 2017 | Televison & Video

1 Answer

No signal on tv screen


Is it registering the correct input? HDMI/ AV1/ AV2/ SCART!

Nov 05, 2014 | Televison & Video

2 Answers

Weve got a toshiba tv model 289s4A & want to plug our ps2 into it, cant find how go get the av channel on the tv. We have connected the av cables but when you change channels on the tv, theres no...


If you have the remote, look for the source button. It should allow you to toggle the settings.

Otherwise they are usually after channel 2 as in Hdmi, Av1, AV2 etc..

Good luck

Dec 09, 2010 | Toshiba Televison & Video

1 Answer

Not sure if this is the tv or what. Was watching this tv yesterday. Then suddenly all other channels except for the one I was on either had squiggly colored lines or 3 mirrored versions of the picture. Now...


Does it happen on other inputs? If so, reset the tv, sat or cable box, unplug power and try again. Play a dvd. Does it happen on a dvd? If not, there is an issue with your cable source. If it shows on dvd too, contact your tv manufacturer. You need a repair.

Jul 27, 2010 | Sony KDF-E42A10 42 in. LCD Television

1 Answer

When I try to set our TV to locate digital channels, the menu skips the channel selection when I scroll through options of picture, audio, channel, lock, setup. All the options are available.


It sounds like your TV is on a different input. If you watch your cable from an external cable box, and this box is plugged into your TV using wires that are yellow, red, and white, or red, blue, green, red and white, you're currently watching TV on a different input than the one used for the antenna. Channels in a TV are controlled by the tuner. The tuner is the silver, threaded, post on the back of a TV, DVR, converter box, or VCR, that you plug an antenna or cable wire to. The tuner contols channels while the other inputs on your TV carry a direct signal like a computer to a monitor. So when you use something other than coaxial cable to connect cable to your TV, you can't access the channel menu while on that input. To access that menu, change the TV's input or source to TV or stop when you see a channel number on the screen. You have to be on the TV or tuner input in order to access the channel menu. If you're on any other input such as, S-Video, AV1, AV2, component (Yp Br Cr), HDMI, etc. you will not be able to do a channel scan. You have to be on the right input or source.

I hope I've provided you useful assistance and that this information allows you to make an informed decision as to how to proceed from here. Please be sure to vote on my response. I hope I've earned a good rating from you today.

Please post a comment if you need additional assistance so that I can help you further.

Jul 27, 2009 | Televison & Video

2 Answers

I need to hook up to digital cable


Connect the cable to your TV's antenna input jack. Through the TV setup menu, perform a digital cable search. This is a separate operation from the full channel scan. The TV manual says this may take up to 10 minutes, so be patient. The set should find the channels on your system. When you want to watch TV, press the INPUT button on your remote to select Digital RF as the source. Press INPUT again to select any other source (DVD, etc.) you have connected when you want to watch that.

I was wrong about needing a converter. This TV has a tuner that can pick up the cable channels if they use a system called QAM. Verizon says QAM-capable sets don't need a box for non-scrambled or premium channel, so you should be good once you have the TV scan channels.

I couldn't find the DP26648 manual at Sanyo's site, so my solution is based on the DP26647 manual. They should be similar. You can download the manual here if you don't have the manual for your set.

Apr 01, 2009 | Sanyo DP26648-R 26 in. LCD TV

2 Answers

The who input button


usually a tv that doesn't "see" video on the S-video will not even "switch" to it.  It just goes to the next Svideo, RCA etc..  
Make sure your cable is not damaged. (on both ends) Does the svideo source and svideo cable work with another tv or video device?
31GT740 Manual From the Manual:   " WHO•INPUT In TV mode, press WHO•INPUT to toggle through the available Video Input channels (VID/SVID and the current channel). In SAT mode, press to select available channel lists.
Using the WHO•INPUT Button Use the WHO•INPUT button to toggle through the available input sources (VID and the current channel) and view the content from the component you have connected to the TV. 1. Press TV to place the remote in TV mode. Make sure that the content from the component is turned ON. 2. Press WHO•INPUT to tune to the available input source and view the component. 3. Press WHO•INPUT again to tune back to the channel you were previously watching.  "
James Mac

Sep 10, 2008 | GE 31GT740 31" TV

1 Answer

Input problem


If you have the original remote, hit video, source, or input button, if it dont have them, then try to change the tv to channel 00 (zero or zerozero), if not then the channels might have to scroll to it, from channel 02 down to make it loop, if it goes to the next highest channel, then you need a remote. It may be set in the menu options to have the video source not saved to your list of saved channels. when you scan the channels, the tv might not look for the A/V source (audio / video), maybe just the RF source. The 3 DVD RCA wires are 1 video and 2 stereo, one stereo for left and one stereo for right. The TV has only 2 , 1 for video and 1 for mono 1 channel sound. This wouldnt have anything to do with why you cant use the DVD player. but try that with the original remote (or a universal remote that is set to your tv set that has either video, input, source or something similar. It is what tells the tv to change from the cable source (RF) and the AV source (the Red White and Yellow plugs, in your TV's case, 2 plugs, one yellow and the other either red or white or something). Dont really know how to explain it much more but hope it helps.

Jan 05, 2008 | Sanyo DS24205 24" TV

3 Answers

DS24205 TV INPUT PROBLEM


if you have a sky remote or know someone who does you could try programming it by using one of these codes, try them all one at a time

Sanyo 0159, 236, 073, 100, 064, 174, 185, 367, 039, 245, 246, 398, 241, 572, 583, 037, 132, 182, 244, 191

Jan 05, 2008 | Sanyo DS24205 24" TV

1 Answer

Need help getting PIP to work


You don't have a problem except you need two tuners. You say you have a VCR, which this has a tuner. Set your VCR to TV and and start the PIP and choose your VCR as the second source. You will now be watching two different channels, one from the TV tuner and one from the VCR tuner. Also just to clarify, you should have the cable wire from the wall running to the INPUT on the VCR and then a cable running from the OUTPUT on the VCR to your TV to make this all work correctly.

May 24, 2007 | Philips 42PF7320A 42 in. Plasma HDTV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yes Televison & Video Experts

Marvin
Marvin

Level 3 Expert

85111 Answers

NOEL
NOEL

Level 3 Expert

8517 Answers

ray gallant
ray gallant

Level 3 Expert

63604 Answers

Are you a Yes Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...