Why are micosoft jigsaw not down loading ? - XP Microsoft Computers & Internet

To replace the quick release blade holder on a Ryobi jigsaw, you will need to follow these steps:

1. Unplug the jigsaw and remove the blade.
2. Turn the jigsaw over and locate the blade holder.
3. Use a Phillips head screwdriver to loosen the screws that hold the blade holder in place.
4. Once the screws are removed, you should be able to lift the blade holder out of the jigsaw.
5. Insert the new blade holder into the jigsaw, making sure that it is properly aligned with the blade clamp.
6. Secure the blade holder in place using the screws that you removed earlier.
7. Reinsert the blade into the blade holder and make sure that it is properly secured.
8. Test the jigsaw to make sure that the blade holder is properly installed and functioning as intended.

It's important to be careful when replacing the blade holder on a jigsaw, as the blade is sharp and can cause injuries if handled improperly. Make sure to use caution and follow the steps carefully to avoid accidents.

Quick-Change Blade Mechanism
Higher-end models, such as the Linefinder Orbital Jigsaw, feature a clamping lever to hold the saw blade. To change a blade, switch off the jigsaw, unplug it, and let the used blade cool down. Pull up the saw-blade locking lever and let the used blade fall out with a slight shake. Turn the jigsaw upside down. Hold the fresh blade with its teeth forward; insert the blade shank into the blade holder as deeply as it will go. Release the lever and wiggle the blade to confirm that it's snugly in place. For models with rollers, such as the Accu-Trak, nestle the blade against the rollers.
Clamp or Hex Screws
Loosen the pair of screws -- on the front of the mechanism of models such as the single-speed jigsaw -- a full turn counterclockwise with a flathead screwdriver, but do not remove them. The used blade will fall out. Insert the new blade fully into the clamp. Lightly tighten each screw alternately and then fully. On older models, you may find a single hex screw on the side of the blade. Loosen this enough to remove the blade, and then insert a new blade carefully so the teeth face forward. Retighten the screw.

Most Dewalt manuals are available here: https://servicenet.dewalt.com/Home . There are 40 Dewalt power tools with 321 in the model number. Several are jigsaws. There are two types for the DW321 (TO3PAK-2LE JIG SAW) jigsaw. Please look at the label on the jigsaw to ensure that you get the correct model and type. The direct link to the manual for the DW321 Type 1 is currently https://servicenet.dewalt.com/Products/GetDocument?docName=402086-01,DW321.pdf&productId=2841&productType=3001&documentId=24909&translatedFileName=http://documents.dewalt.com/documents/English/Instruction%20Manual/402086-01,DW321.pdf .

To change the regular blade on the DW321 type 1, unplug the power tool. To remove the blade, pull the knob on the top of the jigsaw up about 1/4". Rotate the knob counterclockwise until the clamp opens. Do not force the knob after it stops. Insert the blade making sure that the back edge of the blade fits into the support roller. Rotate the knob clockwise until it clicks and then push it down.

I hope this helps.

Cindy Wells

moden jigsaw blades are held in with a taper chuck system
disconnect the unit from the wall socket
push the spindle all the way in
now press on either side of the blade holder and that should move down releasing the blade
now while holding that section down turn the unit right side up and the broken bit should just fall out

Photo editing softwares on the computer performs with the camera once connected. Internet enabled computer provide downloads from micosoft network sites. For example, once displayed a microsoft internet page, search to acquire photo editing softwares to be downloaded onto the computer. Several softwares may be required to acquire the most user friendly with the camera.

Most Bosch jigsaws have a handle on the top of the main handle that you need to pull up and rotate counterclockwise to allow the screw to accept the blade. Insert the blade and rotate 90 degrees into position then tighten the handle and press back down into place. In the beginning it may seem like you are going to break the handle pulling it up but rest assured it will get easier as it gets used.

this saw has 3 orbital settings and one straight line setting .. in orbital mode the blade moves forward slightly on the up stroke and back on the down stroke .. it may be difficult to see and may not be pronounced without a load ...

On the top of the Makita 4304T is a knob, (Top/Front)
This is the blade Installing Lever.

Viewing the jigsaw in the direction you would use it, the Installing Lever is turned towards the Right. Keeping it turned, you then install the jigsaw blade. Once you have the blade up in the Blade Holder, gently release the Installing Lever.

This is a PDF file of the Owners Manual for the Makita 4304T Jigsaw,
(From Makita - Products - Support)

http://www.makita.com/en-us/Assets/images/Products/4304T/owners_manuals/4304T.pdf

[Should the above direct link not work for you, this is Makita - Products -Support, and the download page,

http://www.makita.com/en-us/Modules/Tools/ToolSupport.aspx?ID=248

Left-click on Owners Manual next to the PDF file Icon]

might be cam or eccentric problem