Saws - Recent Questions, Troubleshooting & Support


Refer to instructions that came with saw.
Big hint page 8.
https://cdn.makitatools.com/apps/cms/doc/prod/LS1/897774cd-1c1a-499f-8fa6-bc296110a9d6_LS1016L_IM.pdf

Makita Saws | Answered 22 hours ago


During the whole process be aware of the edges of the flooring that is going to stay. First prepare the area for dust control. Mark the boards to be replaced. With a flat wood bit in your drill, bore a hole near, but not at both ends of the pieces being replaced. Bore only to the sub-floor. Set your circular saw to cut thru the flooring but barely touch the sub-floor beneath. Make two passes with the saw about 1/2" in from each edge. Lift out the center of the piece being removed. With a sharp chisel split the small end pieces at each saw cut and remove. With a chisel, tap the groove side of the piece toward the middle and remove. There may be a little chisel work to get it out. There will be a bit more chisel work on the tongue side. Chisel the tongue side until the fasteners are located and remove them. Remove the piece completely and remove any paper between the flooring and the sub-floor. Vacuum the area to prepare for the new board. Lay the new piece next to the opening and mark the length. If this is end match, t&g at teh ends cut the ends square. I mark heavily and leave my mark when I cut. It can be cut again if it is too long. Choice here are, cut the bottom of the groove and or the tongue off the new board. I leave the tongue and hook the piece in place. Easier to remove it though. Back cut the length on a table saw, being careful not to reduce the size of the face. This will make the bottom of the board narrower than the face. A sander can be used if no table saw is available. Once sized put glue on the sub-floor and put in the replacement piece. If the tongue was left, it must be tapped sideways to get to the point where it will drop in. Do not hit the wood directly. Used a scrap piece as convincer. When lined up, use a scrap piece of wood to drive the new piece down into place. The new board will be thicker and will need sanding. Congrats.

Saws | Answered 3 days ago


Sent you the manual RomaRamey.

Saws | Answered 3 days ago


CHECK THE RETURN SPRING

Blade Saws | Answered 3 days ago


Refer yo instructions that came with saw.
Hint: https://www.manualslib.com/manual/904156/Black-And-Decker-Js500.html?page=2#manual

Black & Decker... | Answered on Jan 19, 2019


yes there is a can not attached it is to lages

Makita Saws | Answered on Jan 19, 2019


check out if belt slipped or sprocket loose

Saws | Answered on Jan 19, 2019


maybe the end of the pin has sheared off

Craftsman Saws | Answered on Jan 19, 2019


If leaver goes right down yes but might just be bits of wood stopping it from tightening maybe wrong way round or thickness is wrong but i have one good brand 20 years and never had a problem with torsion i would clean well before giving up good luck .

Ryobi Rj165v... | Answered on Jan 18, 2019


Hi Helen,
Push the reciprocating head protecting your hand with a glove if necessary. All the way to a center point just above the shoe or table of the tool. Then loosen the two fasteners that bind the blade keep horizontally from the spool head. An Allen head is a six sided wrench. Where a Torque style is a star style. Either equivalent in a T-handled wrench works best. On to removal.

Support the spool head from shifting around with one hand whilst torqueing the fastener counter clockwise to remove or loosen it to free the blade. Should the blade be seized or jammed in the well of the spool head. Use a pair of needle nose plyers to free the blade by vigorously shaking then pulling.

All of this should be done with the electrical plug removed from power to protect your safety. For me. Safety glasses should always be worn.


Performance Power Pendulum Jigsaw 550W PJS550 customer reviews product...

May all your projects be prosperous. Fare. Well.

Black & Decker... | Answered on Jan 18, 2019


I do not have one but this gent does and he may be able to help just post your question. https://www.youtube.com/watch?v=_mVaasDqiSI

Saws | Answered on Jan 18, 2019


Here is the main service document:https://documents.milwaukeetool.com/54-40-6531.pdf

depending on the switch you're using, as mentioned in that document, here are the wiring diagrams:
https://documents.milwaukeetool.com/58-01-0291.pdf
https://documents.milwaukeetool.com/58-01-0293.pdf

Found these, simply by searching Google.

Saws | Answered on Jan 17, 2019


call a stihl dealer

Stihl Saws | Answered on Jan 17, 2019


Google (nutools)(ms200)(manual) without parens OR contact Nutools directly with your request.

Saws | Answered on Jan 17, 2019

Not finding what you are looking for?
Saws Logo

15,639 questions posted

Ask a Question

Usually answered in minutes!

Top Saws Experts

Tom Chichester

Level 3 Expert

50010 Answers

ray gallant

Level 3 Expert

57262 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2000 Answers

Are you a Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...