Where is the drain pan located? - Kenmore 63942 Dryer

If there is a drain plug, it will be on the bottom transmission pan. If no drain plug, the transmission is drained by loosening the pan bolts and lowering one end of the pan till most is drained. Then remove the pan.

You will have to get under the vehicle and find the oil pan directly under the engine. On the oil pan you will locate the bolt to drain the oil pan. They usually are at the lowest point on the oil pan so that all the oil is drained from the pan when removed.

Do u mean the evaperator drain pan.Were is it located in attic or in house closet.Because the condenser fan motor and coils are located outside.BUT ANY WAY DRAIN LINE MIGHT BE CLOGGED OR IN PAN-BLOW COMPRESS AIR INTO DRAIN LINE.CK END OF PIPES FOR CLOGG.

I am a certified HVAC Technician. I have worked in the field since 1996. I have seen this hundreds of times, if not a thousand times, in the past. Every central air conditioning and heat pump system comes with TWO drain pans, The MAIN drain pan is located within the AIR HANDLER (blower) UNIT, while the EMERGENCY DRAIN PAN is extremely LARGE and sits under the ENTIRE AIR HANDLER (blower) UNIT. The ONLY time water will be INSIDE an EMERGENCY DRAIN PAN is when the MAIN DRAIN PAN condensate drain line is CLOGGED, causing the MAIN DRAIN PAN to overflow. What causes the drains pans OR the drain lines to become clogged is slime and scale from the condensate water as well as debris from within the attic that may have either been blown by the air or may have simply have fallen into the emergency drain pan; or some insects from the out of doors have traveled up into the PVC Drain line and built a nest on the downward side of the P-trap. The P-trap is designed to prevent critters from entering your home through the PVC drain lines. Most CLOGS occur at the P-TRAP location.

The BEST thing to do is:

1. Locate the WHITE PVC drain pipe outside your house and ensure there is NO water draining from it.

2. Locate the same WHITE PVC drain pipe inside your house. You should notice a "TEE" where two WHITE PVC drain pipes merge into ONE WHITE PVC drain pipe.

Follow the below steps, in the order shown:

A. FIRST, find another person to act as your second set of eyes at the end of the WHITE PVC Drain Line that is located outside of your home. That person will be looking for water or debris to EXIT the end of that WHITE PVC DRAIN LINE.

B. SECONDLY, locate the WHITE PVC "P-TRAP" inside your house. It is normally located within a couple to three feet of your indoor air handing (blower) unit.

C. THIRDLY, very gently lift the entire WHITE PVC drain line up in the air as high as you can without breaking it, and slam it down onto the rafters or attic floor or garage floor. You are attempting to dislodge the CLOG within the drain pipe WITHOUT having to actually CUT the PVC and without damaging or breaking the WHITE PVC. Depending on how old the system is, it may or may not be brittle; and it may not take much to damage or break the PVC, which will cause leaks. So, be very careful at this point.

D. Ask the person outside if anything has started to EXIT. You can ALSO usually hear water start to drain if you put your ear up to the drain line. If the person said "NO"and if you don't see the water level getting LOWER in the EMERGENCY drain pan, then REPEAT step "C" above.

E. If the person informs you that there IS water now starting to exit the WHITE PVC DRAIN PIPE, you should then wait until all water has drained from the EMERGENCY DRAIN PAN; and then pour at least 1 quart of BLEACH down that drain, from the EMERGENCY DRAIN PAN exit. The BLEACH will further clear out any SLIME which may be remaining within the "P-TRAP" and will also CLEAN OUT and DISINFECT that drain line.

If the above steps do NOT work for you, then prepare to go into the next LOGICAL phase of your attack. Please NOTE: I am limited to 10,000 characters in my response, so I'll repost additional STEPS in another RESPONSE. Good Luck!!!

transmission filter in the bottom of transmission bolted to valve body.you need a large drain pan.place drain plug under transmission oil pan.remove transmission oil pan drain plug.let all transmission fluid drain out then screw back drain plug in oil pan.then you need to remove transmission oil pan then remove filter and replace pan gasket also.make sure you have right amount transmission fluid on hand.buy extra because if you short of fluid you cant drive car if fluid level too low.make sure you get the right amount fluid.torque pan bolts to 96 inch pounds.

the oil drain plug is located on the bottom of the oil pan or at the bottom of the oil pan on the corner were the pan starts to become the side of the pan.it should take a 13mm(1/2")wrench.

Check you drain system. If you are mechanical unplug the unit and remove the back cover at the bottom. Locate the drain tube running down to the drain pan. If it is frozen, use a hair dryer to thaw it. If it is clogged with debris, vlean it out. Locate the drain pan under the evaporator coil and pour hot water down the drain until it is clear. Sometimes the defrost element is positioned to far away from the drain pan so carefully reposition it closer to the pan.

silicone the corners

It only has 1 oil pan which is call a dual resreve. One oil plug is a the bottom of the pan the other is at the front of the oil pan. Look at the front of the oil pan for the other drain plug. Make sure on how many quarts of oil it takes. ( I know 5.0 take 5 quarts including oil filter. But then again its a van double check)