Python model 533/ 7754P My remote start is not working every time I press the start button "remote start error" shows up is there anyway I can fix it myself I got the install in another state so I can't go back to the place of install nor do I care to take it somewhere else please help!

A 7701P is a remote transmitter. It is not an alarm. You must know the alarm's model because different models have various ways of programming transmitters. In other words, you do not program the 7701P. The frequency is already fixed. You must program your security system to teach it that transmitter's code. Look up the manual for your security system. Instructions will be there. This typically involves turning the ignition on/off a specific number of times and pressing a valet/programming button (or switch) a certain number of times and then pressing a button on the transmitter.

To program additonal remote; open door, turn ignition on. Press and release valet button one time then, press and hold valet button. While holding valet button, press lock button on new remote. Turn ignition off. Test system.

I had the exact same thing happen with my 4-button 474p remote. WITHOUT REMOTE START the correct sequence is:

1. Enter car - Leave door open.

2. Turn key to "on" position.

3. Within 5 (five) seconds press the Valet button 7 times then hold down. (Programs to channel 7)

4. Watch alarm light - It should now flash 7 times.

5. While still holding down the Valet button - Press the "lock" button on the remote and release. Should get a "chirp"

6. Now release and repress the Valet button once, holding down. You'll get the "chirp". Release Valet button.

7. Turn key "off". Exit vehicle and test remote. All 4 buttons should now work.

is the message bank full? did you try a hard reboot?

It sounds like the factory alarm is setting up. To make sure the factory alarm does not come on you should make sure all doors are closed before you actually hit the remote to lock the doors. Do not lock the doors with the switch on the door. Make sure you use the Python remote only and all doors closed before you press the lock button.

You have the 24 hr timer on and you just have to press the lock and remote start buttons at the same time.

The "pair" the remote with your system:

1.PRESS AND HOLD the f button on the remote UNTIL the transmit LED lights solid (approximately 10 seconds)
2.PRESS AND HOLD the remote start button (circle arrow) UNTIL the LED blinks 3 times and the amber transmit LED lights up. Your remote is now ready to pair.
3.. Turn the key to the on position
4.Within 5 seconds PRESS AND RELEASE the control button on the antenna.
5. Within 5 seconds PRESS AND HOLD the control button. The status LED will flash one time and the siren will chirp to confirm that the system is ready for remote pairing.
6. Press lock button on remote. System will respond with chirp toconfirm pairing.

To program remote:
turn ignition on
press and release programming switch once ( the siren/horn will honk once)
press and hold programming switch
while holding programming switch, press lock button on remote ( the unit will chirp/honk to confirm programming)
release programming switch
turn ignition off
test remote

usually a combination of 2 buttons so the car doesnt start accidentally.

Depending on the number of output channels - the installer could have installed on any of the channels and that would dictate which buttons to press.

if it is not set on the AUX (output 2) button, then try...

1. Lock + unlock at the same time - output 3
2. * + AUX at the same time - output 4
3. Lock + Aux at the same time - output 5
4. Lock + * at the same time - output 6

You have not given the model # of the unit - so these are viper's STANDARD remote controm configurations.

CLICK HERE to enter your correct model # and Download your instruction manual.

Hope this helps.

Thanks for using FixYa - a FixYa rating is appreciated for taking the time to answer your FREE question.

The P stands for programming. It's used when setting up the alarm system, you would need the manual for the system to tell you what can be done. I have a Python 990 and I can change pretty much everything from sensor adjustments, amount of time it turns over for starting, disabling the siren and many other settings. I found out the hard way one time when I accidentally pressed it and turned the key off and it disabled the siren. I think that's how it happened, been a while since it happened. I would have to get the manual out to be exact. You can also do the programming by pressing all 4 buttons at once and hold for 2 seconds. But you still need the manual to know what your doing. Hope this helps