Fisher and Paykel WL26CW2 Top Load Washer Logo

Related Topics:

A
Anonymous Posted on Apr 15, 2014
Be the first to answer

I have a fisher pay keel washing machine with electronic board it says fault 249 when I get to spin . What should I do ?

Answer This Question

5 Related Answers

Anonymous

  • 92 Answers
  • Posted on Feb 22, 2008

SOURCE: IW712- fisher paykel intuitive eco.

I BELIEVE THAT IS A ROTOR SENSOR ERROR
REPLACE THE ROTOR SENSOR

Ad

Anonymous

  • 22 Answers
  • Posted on Oct 21, 2008

SOURCE: washing machine will not spin or drain

look at my post "eco smart won't drain, smells hot". It could be something stuck in very lowest part fo drainage area. you have to remove the motor on bottom of washer to see into this area and remove blockage.

Anonymous

  • 145 Answers
  • Posted on Apr 20, 2009

SOURCE: Fisher Paykel washing machine model # GWL15 drips

Hi Dale..
It sounds like you have a leaky inlet valve assembly. The part number is 421029P and is easy to replace. You can get one here:
http://www.fisherpaykelparts.net/ecart/item.php?item_id=266&category_id=56

Anonymous

  • 10 Answers
  • Posted on Aug 03, 2009

SOURCE: Fisher & Paykel GW612 Top Loading Washing

Hi there
That fault is the pump blocked error (no change in water level).
i have a quick and easy way to solve this problem.

first turn the machine off then tilt the machine back and lean it on something(a chair or wall), look underneath, in the top right hand corner of the plastic outer boul you will see a small pump motor it has a fan on it spin this fan and if it is hard to turn that means there is somthing stuck in the drain pump keep turning the fan and try to free whatever is stuck in the pump, then try the machine on spin again all goin well the object in the pump should come out with the drain water(doing this will not harm the machine) if the object is still stuck you will need to get the water out of the machine (bailing or siphioning will work) and tilt the machine back again and take the wires off the pump and there should be a white tab on the boul holding the pump on pull this tab and twist the pump anticlockwise about a quarter turn(you will need a few towels or a boul or bucket to catch the water) and it should come off exposing the blockage.
Hope this solves your Problem.

Nick

Anonymous

  • 2 Answers
  • Posted on Sep 30, 2009

SOURCE: Our Fisher & Paykel Washing Machine is not

Emptied washer, tipped it on its side, detached drainage pipes underneath, and pulled out old fabric/lint/blockage with tweezers. Plugged in, switched on, all good.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do you resolve Fisher Paykel fault code 249
From Service Manual for 249 error

249. (11111001) SmartPump Timeout Fault (No change in the water level)
While draining, the water level reading from the pressure sensor has not changed for 3 minutes.
This fault will generally be caused by a problem in the pump system, from either a blockage, or restriction in the pump system. This fault will also flag if the machine is 'By-Passing'.
Primary Source: Pump System
Action: 1) Check that the drain hose has not been kinked.
2) Check the length of the drain hose. A 1-meter extension
hose of the same diameter fitted to the existing drain hose is
the maximum allowable length.
3) Check that the machine is not pumping to a head that
exceeds the pumps limits (2.4metres is the maximum head
height).
4) Remove the inner bowl and check that the pump hood hasn't
been fitted around the wrong way.
5) Check for lint streaming from the pump hood that may be
blocking the pump cap inlet.
6) Remove the pump hood and cap, check for lint, grit and
debris.
7) Check for free movement of the impeller and that the impeller
hasn't come off the rotor.
8) Check for free movement of the flapper (replace if broken or
damaged).
9) Check for lint and foreign object in the ports of the pump
housing.
Read full answer
Jun 23, 2015 • Fisher and Paykel Washing Machines
tip

Decoding Fisher & Paykel Electronic Washing Machine Fault Codes
The Fisher & Paykel Smart Drive and EcoSmart electronic washing machines are equipped with fault detecting software to help easily determine the cause whenever a problem occurs. Not like other electronic washing machines, these ones do not have displays to flash the code, but rather use the eight (8) light-emitting diodes (LED) of the Wash Progress indicators to indicate the fault code. The eight (8) LEDs stand as an 8-bit binary number (zeroes and ones) that must be decoded and then converted to the decimal number system to get the fault code.

The fault code can be decoded by determining which Wash Progress LEDs are lit. Once determined which of the LEDs are lit, write down the 8-bit binary code; 1 for lit LEDs and 0 for the off ones. For example; the final wash, rinse, and spin LEDs are lit; the binary code is 00001101. This in turn can be converted to the decimal number system by multiplying each digit with its corresponding place value then adding up the result. From left to right, the place values are 128, 64, 32, 16, 8, 4, 2, and 1 respectively. Therefore, the decimal equivalent of 00001101 is 128(0) + 64(0) + 32(0) + 16(0) + 8(1) + 4(1) + 2(0) + 1(1) = 8 + 4 + 1 = 13; the fault code is 13 which is a pump fault.

Once the code is determined, search the web for the meaning and indicate it when requesting for an online assistance to facilitate a quick and precise response.
Read full tip
on Apr 14, 2010 • Fisher and Paykel GWL11 Top Load Washer
0helpful
1answer

Fault code 9 fisher and paykel
Hi,

With the board replacement, did you program this board for this unit? If not, thats the problem you have now. Good Luck

I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

Read full answer
Aug 04, 2014 • Fisher and Paykel WL26CW1 Top Load Washer
0helpful
1answer

Fisher and paykel washing machine fault code 9 how to fix
All replaced electronic boards need resizing.
Going by your post your have an AquaSmart machine
Here are some details to resize an AquaSmart machine

24903416-ei0rt0v231vo43kgyqwiblfx-4-1.jpg
Read full answer
Aug 03, 2014 • Fisher and Paykel WL26CW1 Top Load Washer
0helpful
1answer

I have a fault code 249 from my Fisher and Paykel 8kg washing machine. What does this mean?
I didn't know the codes went this high! it will be a motor controller fault I would suggest, as all other faults above 140 are motor controller.
Read full answer
Aug 28, 2013 • Fisher and Paykel (IWL12)
0helpful
1answer

What does fault code 30 mean on a Fisher and Paykel washing machine Model GWL15/IWL16?
it means that the two electronic boards in your machine are out of sync and need to be reset. just turn the machine off at the wall for a minute and then back on. if this doesn't fix the problem, you will need to replace one of the boards, which one is unknown until you try.
Read full answer
Aug 14, 2013 • Fisher and Paykel Fisher Paykel Intuitive...
0helpful
1answer

Fisher & Paykel model WL26CW2 is throwing error code 249. Any suggestions on what the problem is? I am having trouble locating a manual and my searches haven't been productive.
Here is the fault code guide for Fisher Paykel.
Read full answer
Nov 06, 2012 • Fisher and Paykel WL26CW2 Top Load Washer
0helpful
1answer

Spin Led stays on and beeper beeps
this spin light that is on is a fault code no:1 which means the electronic motor control has a memory problem solution replace motor control module ... hope this helps..:0)
Read full answer
May 24, 2010 • Fisher and Paykel GWL11 Top Load Washer
0helpful
1answer

Irecieved a fisherpaykel ecosmart washer from a friend. it has an electronic display board and it keeps stoping.one yellow wash light and one yellow rinse light comes on and it starts beeping,after a...
Tell us from left to right which lights are staying on to see what the fault code is for diagnosis.Cheers.
Read full answer
Aug 08, 2009 • Fisher and Paykel Fisher Paykel Intuitive...
0helpful
2answers

Fisher paykal top load washing machine
I had the same problem. I unplugged the machine for a while (overnight) and it then worked properly when I plugged it back in. Probably just a circuit board issue that was cleared with the power removed.
Read full answer
Sep 02, 2007 • Fisher and Paykel GWL11 Top Load Washer
Not finding what you are looking for?

View Most Popular

WL26CW2 Top Load Washer

  • Washing Machines

Related Question

How do you resolve Fisher Paykel fault code 249

  • Fisher and Paykel Washing Machines

61 views

Ask a Question

Usually answered in minutes!

Popular Questions

Error code 37

Fisher and Paykel Fisher Paykel...

Washing machine won't turn on

Fisher and Paykel (IWL12)

Washing machine not draining and finishing cycle

Fisher and Paykel GWL11 Top Load...

Blocked filter in Fisher & Paykel washing machine top loader

Fisher and Paykel IWL12 Top Load...

Error code 130 & 240 how do i fix this

Fisher and Paykel Fisher Paykel...

Top Fisher and Paykel Washing Machines Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...