No Power Spin-up

My friend, there is no starter relay as such. The integrated power module, under the hood, has electronic control for starter motor. In the diagram, red wire is voltage to starter motor, hot all the time, voltage comes from battery. The other color wire at starter is voltage, comes from integrated power module. The integrated power module receives input data to control starter motor, so other systems are involved.
Any applicable trouble codes? Make sure battery has a full charge and battery connections all good. Usually you test can starter motor by removing, laying on the ground, hook up jumper cables properly from battery to starter motor, at the least, it should kick out drive gear and spin? If not, I'd suspect the starter. I can only help with testing. Any testing at starter, on vehicle, make sure tranny is in park or neutral and parking brake is set. Did you try cranking in neutral?

Hello Gloria Starling,

The answer is not going to change much... even without the make & model... but it could be said with more conviction...
You have one & only question ... Sadly no make or model came thru with the question...

While this is LARGELY a USA site... GLOBAL products have been able to get satisfaction here as well...


Dryer spinning is LARGELY the function of the drive motor...
or
The DRIVE BELT.

In the USA you need only go to one of the many Parts houses
and input you make & model...

Issuing forth in great abundance will be PARTS PRICES and procedural videos...

The (opinion) worst prices a pushiest sales folks .... come from one of the BETTER on-line technical DATA... domes from SEARS...

If you take my advice & buy your belts/motors & pulleys...
only after getting MULTIPLE ESTIMATES ... You stand little chance of finding how pricy & pushy SEARS agents can be...

Input your details below:
appliancepartspros.com
repairclinic.com
partsselect.com

Search Over 2 1 Million Appliance Parts

Appliance Parts Lawn Mower Parts Heating Cooling Parts 365 day

returns http://repairclinic.comartssellect.com/


Appliance Parts Lawn Mower Parts Heating Cooling Parts 365 day returns

1) You must have the deck belt is WORN, to due the lack of maintenance , however LUBE the deck belt with 100% of silicone or wax
2) Lube the rollers bearing with wd-40
3) Test the drive belt motor and replace if necessary
4) Test the input voltage motor, if there are the motor need repair.see my personal TIPS for motor help
5) Test the output voltage board, for input voltage motor, if there are NOT the board is faulty. see the block diagram
God bless you

test the fuse and replace, reset the c. breaker and try again
2) test the power cord.
3) test the drive belt motor, for worn, or adjust
4) test the input voltage motor, if there are the motor need repair
5) test the output voltage board, for input voltage motor, if there are NOT the board is faulty.
God bless you

Possible that there is no power to the motor after the cycle is triggered. It can be failure of the drive relay or board , check the output to the motor at the time of the cycle to confirm, if no voltage if present this can be related to the board, if there is voltage check the motor and drive for friction. Check the drive belt.

Hi,

I am sorry to hear regarding the trouble.Unfortunately, this is not an easy or small fix.

The F-6 is a motor tachometer errorhere is what the units Technical data sheet shows.

Drive Motor Tachometer Error

The control is unable to properly detect motor speed and the machine will shut down.

If a failure occurs during high-speed spin the door will be unlocked after 3 minutes.

Potential Causes

• Check wire harness connections between the Drive Motor/Tachometer and the

Motor ControlUnit (MCU), and between the MCU and the Central Control Unit

(CCU)

• Check the Drive Motor
• Check the MCU
• Check the Wire Harness

The drive motor is located on the bottom left side .
The MCU(motor control unit) is also on the bottom left side.
If after checking these, if it still does not spin .
You can check the motor windings. if you have a Volt-Ohm meter.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

DRIVE MOTOR TACHOMETER ERROR

If the control is unable to properly detect motor speed, the machine shuts down.
If a failure occurs during high-speed spin, the door unlocks after 3 Minutes.

Possible Causes/Procedure

1. Verify the shipping system including shipping bolts, spacers and the power cord are removed.
2. Unplug washer or disconnect power.
3. Check drive motor tachometer resistance. It should be approx. 115 ohms.
4. Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU).
5. Plug in washer or reconnect power.
6. Check the MCU by looking for operations of the drive motor.
7. Check the drive motor for powered rotations.

Hi.This will occur when The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after three minutes.

Possible Causes / Procedure

1. Verify the shipping system including shipping bolts, spacers and cables are removed.
2. Unplug washer or disconnect power.
3. Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU).
4. Plug in washer or reconnect power.
5. Check the MCU by looking for operations of the drive motor.
6. Check the drive motor for powered rotations.

Replace failed component.(If the connections between the CCU/MCU/drive motor, are correct, and not severed, thsi will lead to a failed Tachometer, which is located on the motor shaft. The motor will need to be replaced, in this case.)

How are ya? This is kind of technical information that i'm about to give you, so if you're not that technical then you should call a service technician to diagnose. Good luck and thanks for the inquiry :)

F25

DRIVE MOTOR TACHOMETER ERROR

If the control is unable to properly detect motor speed, the machine shuts down.
If a failure occurs during high-speed spin, the door unlocks after 3 Minutes.

Possible Causes/Procedure

1. Verify the shipping system including shipping bolts, spacers and the power cord are removed.
2. Unplug washer or disconnect power.
3. Check drive motor tachometer resistance. It should be approx. 115 ohms.
4. Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU).
5. Plug in washer or reconnect power.
6. Check the MCU by looking for operations of the drive motor.
7. Check the drive motor for powered rotations.

Make sure your roller motor is spinning. If it is, then adjust the rollers tight enough to spin out the wire. If power is available and motor does not spin, check the fuse on the control board. If it is ok, then it is your control board.