Question about Onkyo TX-SR605 Receiver
Even though I can verify a strong signal to all speakers connected, when I run the 2EQ test it cannot locate the rear left speaker. I have the set-up configured to cross over at 100hz using Carver di-polar bookshelf speakers. the right speaker is located.
I double checked that the set up was configured correctly and given that all speakers are audible I am stumped as to why it can find all but that one speaker.
Thank you for your assistance.
The only thing I can think of is that the microphone that detects speaker signals is in a position that blocks the sound from that speaker. When it's testing there should be no noise from anything or anyone.
Posted on Jun 12, 2017
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
I just read over the problem you were having with your Onkyo TX-SR500 receiver. It sound like the unit needs to be setup for all five channels.Sence your symptom says the diplay shows Dolby D3/2.1. According to the owners manual with the remote control look for speaker setup whin the button is pressed the current speaker setup will be shown in the display. Press the preset/adjustment<> to change the current setting to five speakers. the listening mode will automatically change according to the number of channels you selected. Hope this helps. Radiotech
Posted on Aug 14, 2007
Hey Tad, I have the same problem and perhaps a solution. I just moved to the other SW "pre-out" and it seems to be working..the green light is on . Whatever works i guess.
Posted on May 14, 2008
Greg- Powered subs are better than non-powered subs (also known as passive subs), anyway I see the TX-8511 has no sub pre-out on the back panel, so you need to decide what sub you will use and run from the receivers left and right speakers output into a subwoofers speaker in from speakers then back out to speakers, look at the back of a subwoofer and you will see like 4 sets of speaker hookups 2 in and 2 out, what this does is takes the low end or bass and drops the signal to the subwoofer then takes the mids and highs out to your left and right speakers, unless your regular left and right stereo speakers have large woofers a sub is the way to go.
Posted on Jan 28, 2009
I am experiencing issues like this although with a VCR connected with analog video. I added a BluRay DVD player and all of a sudden I lost my video upconversion from my VCR. I am going to try to reset the receiver to see if this fixes the problem. If not, I don't think it is the receiver issue, I think it may be the fact that enorder for video to pass through HDMI, allot of criteria needs to be met. Certain Handshakes need to happen, especially with the HDCP issues. Most likely I will connect a separate video cable to my Plasma and use a secondary input on the Plasma for the VCR signal. You may want to purchase the Component Video adapter for the wii system as this will provide you with at least 480p and your receiver should not have an issue passing the signal over the HDMI output. Good luck and give me an update.
Posted on Jun 17, 2009
This is the only model that I could find. Codes are in the back of user guide. Hope this helps.
Posted on Aug 23, 2009
Tips for a great answer:
Jan 02, 2015 | Onkyo HT-R2295 3D Ready A/V Receiver - 7.1...
Apr 10, 2012 | Audio Players & Recorders
Jun 21, 2009 | Onkyo Audio Players & Recorders
Jun 06, 2009 | Onkyo TX-SR606 Receiver
Apr 15, 2009 | Onkyo TX-SR606 Receiver
Jan 28, 2009 | Onkyo TX-8511 Receiver
Mar 18, 2008 | Onkyo TX-SR304 Receiver
Jan 24, 2008 | Onkyo TX-SR703 Receiver
Aug 14, 2007 | Onkyo TX-SR500 Receiver
7,693 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: