Television shuts off and gives two blink code. We unplug it until it stops blinking then plug it back in. We will repeat this sometimes up to four times before the TV stays on. Works fine otherwise. It may work for a few days to a week before shuts off again. Most of the time only after 1st turning on. Once it stays on, wont shut off. Just a couple of time its shut off after viewing for a while.

UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ON FOR A MOMENT AND GOES OFF.

PRESS AND HOLD "device"(input) and "menu" buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protect the Convergence IC or IC's is blown---set will detect no voltage to convergence IC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES AND THEN TO GET IT TO REPEAT MORE YOU HAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.

MOST OF THESE SETS HAVE A SELF DIAGNOSTIC:

UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ONFOR A MOMENT AND GOES OFF.

PRESS AND HOLD "device"(input) and "menu"buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protectthe Convergence IC or IC's is blown---set will detect no voltage to convergenceIC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES ANDTHEN TO GET IT TO REPEAT MORE YOUHAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM

let me know what you find--hope that you find 2 blinks, a pause and twoblinks--this is the most common and easiest to fix.
SD TECH

MOST OF THESE SETS HAVE A SELF DIAGNOSTIC:

UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ONFOR A MOMENT AND GOES OFF.

PRESS AND HOLD "device" and "menu"buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protectthe Convergence IC or IC's is blown---set will detect no voltage to convergenceIC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES ANDTHEN TO GET IT TO REPEAT MORE YOUHAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM

let me know what you find--hope that you find 2 blinks, a pause and twoblinks--this is the most common and easiest to fix. SD TECH

MOSTOF THESE SETS HAVE A SELF DIAGNOSTIC:

UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ONFOR A MOMENT AND GOES OFF.

PRESS AND HOLD "device" and "menu"buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protectthe Convergence IC or IC's is blown---set will detect no voltage to convergenceIC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES ANDTHEN TO GET IT TO REPEAT MORE YOUHAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM

let me know what you find--hope that you find 2 blinks, a pause and twoblinks--this is the most common and easiest to fix.

Either give me a yahoo or note if light on front of set blinks--count the blinks if it does.

most common is 3 blinks, pause 3 or 5 blinks etc.

Let me know if I can assist you.

SD TECH

next time it shuts down and power light goes out--do the self check.

On front of set press and hold BOTH MENU AND INPUT BUTTONS FOR AT LEAST FIVE SECONDS AND RELEASE BOTH BUTTONS.

Power light (if an error is detected) will blink a two digit code.

Most common is 2 blinks, pause and 2 blinks---set if there is a error code will repeat it at least 5 times.

If you detect a error code, let me know and I will tell you what it means.

SD TECH

Do this and let me know what you find:

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ON FOR A MOMENT AND GOES OFF.

PRESS AND HOLD “device” and “menu” buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protect the Convergence IC or IC’s is blown---set will detect no voltage to convergence IC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES AND THEN TO GET IT TO REPEAT MORE YOU HAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM

I hope you find 2, then 2 error--it is the most easy to fix.

If this information helped you rate this solution as I do this here for free.

SD TECH

this set has a self diagnostic feature:

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;}


UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ON FOR A MOMENT AND GOES OFF.

PRESS AND HOLD “device” and “menu” buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protect the Convergence IC or IC’s is blown---set will detect no voltage to convergence IC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES AND THEN TO GET IT TO REPEAT MORE YOU HAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM
If this has been helpful I would appreciate a vote from you here; if you need direct help:


[email protected]

Hi, thats the code for AKB fault, this requires a tv tech to fix,, not a big bucks repair, video-tek

5 blinks means problem in the AKB (video) and 4 blinks means problem with the verticle deflection. Try this to get the screen to display any recent faults then get back to me and let me know what it said. Press the following buttons on the remote.
Display, Channel, 5, Vol Minus, ( Not plus ) then Power. This brings up
a screen with a list of the problems and number of times they have occurred.
Each of the problem names is abbreviated as, "OCP", "OVP", "V STOP", ETC.
We have repeated them in parentheses in the text for the "Blinks" described
above so you can correlate between the diagnostic screen and the blink
codes.