How do one enter to Service Mode level 3 of Canon irc3200

Hi Teasel850,

There is an internal counter that prompts this message. There is software to reset the counter called MPTool. But why complicate things when it can be reset manually using the following steps.

Reset Canon Pixma MP130 Printer

1. Turn on the printer.
2. Press the MENU key, and then SCAN, COPY and SCAN again - entered the service mode.
3. Select NVRAM ACCESS further OK.
4. Select SET ABS-M LEVEL and set value equal to zero.
5. Select SET ABS-R LEVEL (if any) and is set to zero.
6. Turn off the printer POWER button.

Best regards

Mike

a) How to enter Service mode
Follow the procedure below to enter Service mode.
1) Turn off the printer.
2) Turn on the printer while holding down the [Paper Source] button and [Online]
button.
3) Check that "Canon W8200" is shown on the display, and then release the buttons.
4) Next, "SERVICE MODE" is shown on the display. (If sheets are inserted, this will
be displayed after the sheets are loaded.)
5) Use the [Lower arrow] button to make a selection.
Service mode is added to the options in the Main menu.
Service mode can be entered even during error status (when Exxxx and Wxxxx are
shown on the display) by turning the power off and then using the above key
operation.
b) How to exit Service mode
To exit Service mode, turn off the printer.
c) Buttons used in Service mode
• Selecting menus and parameters: [Left arrow] button or [right arrow] button
• Entering a lower-level menu: [Lower arrow] button
• Entering a higher-level menu: [Upper arrow] button
• Setting menus and parameters: [Enter] button


Now under service mode select counter, and select printer and W-INK to reset it, and under initialize select W-INK.
But also change the waste ink absorber so that you do not get waterfalls of ink from your plotter :-)

Hope that helps

go to service mode place function -clear paswd- ok -then switch the machine off /on

1)Enter SERVICE MODE by pressing MENU-SCAN-COPY-SCAN
2)Enter NVRAM by pressing < or> then OK
3)Set ABS-M to 0
4)OK

It needs to go to a shop to have the absorber changed and the counter reset. Only a Canon shop has access to parts and service mode to reset the ink counter.

Canon MP110, MP130

1. Include the printer.

2. Press the button "Menu" , then "Scan" , "Copy" and once again "Scan" (all - fell into service mode).

3. The Arrow to choose "Counter access" , press "OK" .

4. The Arrow to choose "ABC-M DOT Count" (or "ABC-P DOT Count" - depends on that, evidences what from counter = 100 ) and press "Copy" .

5. The Button "-" throw the counter before "0" , and press "OK" .

6. For leaving from service mode to press "Resume" .Good luck! Cheat that you dispose of problems!

It's a shop repair since you have to take apart fully, and also use diagnostic mode to reset the error.

I am not familiar with this model but usually Canon waste bottle has:

1. Check if the waste toner botlle has some clear portion near the neck, (as in IRC3200) or other part of the bottle ,even the waste toner was removed but if this portion is still clouded by toner the sensor will still detect the waste is full

2. If the situation is not like this some Canon Ir machine needs to reset waste toner counter in the service program mode even the waste toner bottle was emptied

1. turn on.
2. Press MENU, after SCAN, COPY and again SCAN - your are in a service mode.
3. Change NVRAM ACCESS and press ОК.
4. Change SET ABS-M LEVEL and set value to zero.
5. Change SET ABS-Р LEVEL (if this function not hide) and set value to zero. If this function not presents, go to next step
6. Turn off printer by a power button.

Thats all )))

when stop printing you should have posted the problem then, you probable damage the board, you need to replace the booth rom first