Need WR55X10942 instruction sheet.

Hi Cathy.

If you go to this site
Charter net Charter Remote Controls 1060BC2 1060BC3 and put in Sharp as the TV type, it both gives you instructions on programming the Charter remote, and gives you the codes for Sharp TVs (10818, 10093, 10688, 10851, 11602, 12360 in this case)
Hope that gets you up and running!
D

Your refrigerator uses the common GE WR55X10942 control board. On most models you can just swap out the control boards. Some models require a few additional steps, you will have to check your serial number to see if that applies to your model (see instruction sheet included with the control board).

First unplug the refrigerator.

On the back of the refrigerator, there is a panel. Remove the screws and the panel cover.

Unplug wires from the old control board (note where the wires go), and plug them into the new control board.

Plug refrigerator back in and test out.

For more detailed instructions, and pictures click the link below.

How to replace WR55X10942 control board

Go to the Humminbird support website and download the manual. The information you are looking for should be in there.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/saam_2816e29ba1070532

Hi there,

If you've had your vehicle computer codes read and determined no issue with the VSC circuit, then you just need to cancel the warning light.

I've made up the following instructions, on how to clear VSC & TRAC Warning lights:

Zero Point Calibration of Yaw Rate and Deceleration Sensors Using Paper Clips (or jumper wires).

First, locate the 16-pin ODB II connector under the steering wheel (beneath the dash). The pins are numbered sequentially backwards from right to left (from the wide side of the connector looking at it from underneath).

Take two normal-sized paper clips (or suitable jumper wires). If using paper clips, straighten one edge of one of the paper clips. For the other, bend it open to a 90-degree angle (like an elbow).

Insert one paper clip/wire into pin # 14 (Ts), and the other paper clip/wire into pin # 4 (CG) of the OBD II connector - DO NOT allow the paper clips/wires to make contact at this point.
Refer to diagram below:

1. Ensure the shift lever is in "P" range.

2. Turn the ignition switch to "ON" (not start).

3. Momentarily touch the two paper clips/wires together (short) and separate again (open) - Repeat this process 5 times (within 8 seconds of turning ignition on).

Verify that the VSC indicator light is illuminated, indicating the Recorded Zero point is erased.

4. Turn the ignition switch "OFF".

5. Remove both paper clips/jumper wires from the OBD II connector.

6. Turn the ignition switch "ON" (not start) - wait until VSC warning light turns off (approx. 20 seconds), then wait 2 seconds.

7. Turn the ignition switch "OFF".

9. Re-insert paper clips/jumper wires to terminals #4 & #14 of the OBD II connector (as per above diagram).

10. Turn the ignition switch "ON" (not start) - VSC warning light should remain illuminated for 4 seconds, then start flashing at 0.13 second intervals.

12. After VSC warning light flashes for 2 seconds, turn the ignition switch "OFF".

13. Remove paper clips/jumper wires from the OBD II connector.

Drive your vehicle to confirm VSC & TRAC warning lights have been reset and no longer illuminate.



"If this has helped you resolve your issue, please be kind enough to leave a testimonial"

http://pages.ebay.com/help/account/forgot-userid.html
That should help get you fixed up. You could also just create a new account.

On a HP 4266w, Jumper is behind the sheet metal where the cooling fan and radiator is located. You need to remove the three spring screws, fan and sheet metal screws (3), one is deep on the right. Once you remove the clip, holding the radiator, the sheet metal will come off and the dip switch, jumper, is marked. Take the clip off the top and you are ready to go. The radiator clip is tricky to get off as it has a swivel type clip on both ends. I Pushed down one end and lifted the other off.; Take your time. Hope this helps.

Hi,
Please download required user manual copy from HERE.
Thanks.

Hi,

You can download and print the instruction manual in PDF format by clicking this link.

Please note: Adobe PDF Reader is required to view this manual. Click here to download the latest version of Adobe Reader.

Thanks for using FixYa.

Those readings are to low.

Use this software. search on the net to get proper usage instructions. you need a USB cable. Its absolutely free and works!
Regards