20 Most Recent Frigidaire 30" Self-Cleaning Freestanding Electric Range - White-on-White - Page 8 Questions & Answers

F2
Oven temperature too hot
Check and replace oven temperature sensor (RTD).
F3
Open oven temperature sensor (RTD)
Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.
So i suppose its a sensor replacement is necessary.These are the fault code explanations by frigidaire.good luck with the machine.Please do post results and comments.

Hello KC - You may try and reset the cook top by disconnecting the power to the unit for up to 30 seconds by flipping the circuit breaker off and back on. This often clears most false error codes. If the lock symbol does not clear, then the unit more than likely may be experiencing an issue with the EOC (Electronic Oven Control), user interface board or a potential wiring failure. This is not a typicaly do it yourself job; please consult a professional or your manufacturer.

Hello dfleck - Unfortunately once the enamel is burnt or damaged, it cannot be repair and will need replacing. At this point, I would personally recommend consulting with a service technician to proceed further.

Hello meathead4094 - Often when the LOCK light is flashing, it is because there is door malfunction. Try reprogramming the range by either unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes and turn the unit back on. Typically, this will clear the flashing. If issue persists, the range could possibly have a faulty door latch, light switch or EOC (electronic oven control). I would strongly recommend contacting a professional to get the appropriate diagnosis prior to make any unnecessary part replacements.

you may need new heater elements all together

Hello Herb Reinhart - If the range previously displayed DR and now showing F11, it typically indicates that the unit has detected a shorted keypad. Since you have already try resetting the unit by unplugging it and issue persists, I would recommend contacting a professional to proceed further. Most likely the EOC on the range will need replacing.

Hi stormsdestin - Thank you for your post! The electric range, model number FEF353BFW is recommended to used warm soapy water to clean the electric cook top. If your cook top is broken or damaged, you may want to connect with a local servicer who will be best equipped to pinpoint the problem. However, if you are requesting information on what kind of cook top repair creme may be use I would personally suggest contacting the manufacturer directly.

Hi there! From what you have described it sounds like the unit's thermostat and or temperature sensor is not functioning properly. Typically this is not a DIY type of job to complete on your own. Please contact a professional that your manufacturer suggests. Please let me know if you have any other concerns or questions.

Hello wills_amber - Typically, error code F1 indicates that the range has detected a runaway temperature issue (overheating). Try reprogramming the range by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes and if the error code does not clear, I would recommend contacting a professional to proceed further. Most likely the EOC (electronic oven control) on the range will need replacing.

Hi rhass132 - Regrettably, this is not a simple DIY job. Usually this type of information is not release to a consumer and it is very rare to find enough information to do it yourself. Generally, qualified technicians often perform complicated part replacement such as this. If I was in your position, I personally recommend seeking a professional to accurately assist with the repair or installation of the part.

This happened with my 42016 single oven. It was the element. They can be bought online and are easy to fit.

Hello rjshomesnj - Typically error code E20 indicates that the range has detected a communication failure between EOC (electronic oven control) and ESEC system (electronic service element control). In other words, the range has an issue with the switch for the burner. I will personally recommend contacting a certified technician to move forward accurately and to assist with the repairs. You can often locate qualified servicers by visiting the manufacturer website.

Hello Roy Ellis - Try reprogramming the range by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes and restart unit. If it proves to be ineffective, I personally recommend consulting a professional to move forward accurately. The range could possibly be experiencing an issue with a wiring failure, EOC (electronic oven control), sensor probe and/or faulty element(s) which will need further diagnosising.

Hello Veronica Candeleria - I located the manual on the Frigidaire website. Here is the manufacturer link and hope you find all the information that you need. If for any reason you have difficulties pulling up the requested information, I recommend taking off the last letter of the model number so you can pull up the data

Try to turn the circuit breaker off to the home for about 10-15 minutes, then retry the unit. If the door does not unlatch then either the door latch assembly or main control board need to be replaced, since they are not communicating correctly. Consult a professional at that point to be safe.

Hi mannycarla - Typically error code F1 indicates that the range has detected an issue with the runaway temperature (overheating). A certified technician will need to check the RTD senor probe and/or EOC and replace if necessary. Meanwhile try reprogramming the unit by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes and restart range. Usually this will clear most false error codes. If it proves to be ineffective, contact a professional to move forward accurately.

Hi Shannon Turner - Try reprogramming the range by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes and restart unit. If it proves to be ineffective, the range could possibly have a faulty element(s), wiring failure, or a communication error with the EOC. Connect with a professional to accurately pinpoint any potentially more serious issues if issue continues.