20 Most Recent Belkin Wireless-G Plus MIMO Router with USB Adapter and Geek Squad Installation - Page 3 Questions & Answers

Yes....
Make sure that the power is off, and uplug the unit from the back. Then install the memory and plug it back in then power it back up. The computer will see the new memory and so will Vista. I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

If you have the model number of the router you can go to this site and download the drivers.

http://www.belkin.com/support/?lid=en

Have a great day...
Tim

You have to make sure you go to Control Panel/Printers, right click on the printer in the list and click 'Properties' - go to the sharing tab, select 'Share this printer', give it a name, and click OK. Then go to Printers on each of the laptops, select 'Add a printer', then 'Network printer', then 'Browse for printers'. You should be able to see the printer. If all the computers use the same operating system, you're good, otherwise, when you first share the printer, you may want to install additional drivers from the cd to support the different operating systems - alternately, you'll have to install the drivers for the printer on each computer.

Please rate if this helps :)

Hi Houzeman Have you: re-started the computer         power-cycled the router, ie, unplugged unit and waited 10+ seconds, before re-connecting                 disabled the unit, then enabled it checked in Control Panel that the wireless card/ usb adaptor, is enabled; try disable/enable
before checking settings
re-input username and password
re-input security settings?

If you are using a separate modem and router, turn both off, then power-on the modem, before the router.  If you have ethernet access, and a Local Area Connection is available, use it to open a browser and type in 192.168.2.1 (assuming yours is a Belkin) and check your settings.
I use a Belkin, which is a good unit, but it can be cantankerous sometimes, dropping out, then coming back unexpectedly and without reason. Good luck NOEL

YES YOU CAN IT SHOULD HAVE PLUG-INS FOR ETHERNET AND YOUR ISP INLET ON THE BACK OF IT ALSO G+MIMO OFFERS NICE SPEED WIRED OR WIRELESS.

Use this tip as a check list.
Check if you set the correct SSID + Key and "connect if router is not broadcasting" set in your adapter configuration.
If you do not know Key you need to reset from Router.
If you missed SSID you can check on any PC when connected to WLAN and retrieve the name of NON BROADCASTED network

Connect to Router using a Lan Cable.
Open the Advanced user interface page go to wireless tab and be sure radio signal is ON.
Check with my Tip all the step
Let me know if you nees any further info.

You need to have an Internet Service Provider. You connect the router to a modem from the cable Service Provider or through the phone line for BT. Then you can connect wired or wirelessly to internet through the router.

If you describe your set up in detail and tell me the Internet Service Provider I may be able to help more....

take this information and notice the stars:
Start-> Run-> cmd [enter]
ipconfig [enter]
You will probably see:

IP: 192.168.*.2
sub: 255.255.255.0
gateway 192.168.*.*

Go to an Internet Browser and type in this from the *GATWAY* in the address bar:
http://192.168.*.*

* This will likely be 192.168.1.1 / 192.168.1.254 192.168.0.1 /254
* or maybe even 192.168.2.1 / 254

username and pass will be admin admin or admin 1234 admin and no password or maybe no username and admin as the password...
Configure the router as you see fit.

You may have to reset the password which will reset to the router to Default Settings. Do this by using a paper clip to push in the little button in the hole, in the back of the router. You will need to re-adjust your settings if you had Encryption or anything and I would suggest settings a secure password. If you do not like this solution you must guess the password.

There's a big possibility that your computer is set with a static IP, computer should be set to Obtain n ip automatically, follow this Go to control panel and network connection then look for Wireless connection>right click on it and click on properties>look for Internet proptocol TCP/IP from the list>click propeties>a new window will open just set it to both Obtain and then click on OK and close all the window, then after that check if the computer is already getting a new IP if still no restart the computer....

Try lowering the MTU.

Visit Belkin Official Support - F7D4301 Downloads There are two versions of firmware available. Version 4 and Version 1. To downgrade your router firmware, use version 1 firmware. I hope this will resolve your issue.

ok... so I've now installed this on my new pc that i built... first in order to get it to install at all you must download DirectX 7.0 and right click to "--(edit compatibility settings to windows 98/Me and run as administrator)--" remember this as well be doing it a few times. once you do that install DirectX 7.0 and say yes to all. now that this is installed take the .iso file you have and burn it to a cd or DVD-r, once burned you need to go to my computer and right click on the cd/DVD drive, select open (NOT open autoplay), inside the disc menu i want you to go to 2 files... "setup" and "start" need to also have their compatibility settings changed to the above settings. now that these are set stay in the cd menu and double click "setup" this will take you through the setup procedure. after the setup procedure is finished do not view the notes, and continue back to the desktop. now from your start menu load the game and it should run

User Manuals only. Contact them direct http://www.belkin.com/support/dl/f6c1000-tw-rk.pdf ..

you need more than a wireless adapter to connect to the internet......
you need a wireless network to connect to. in cafe's and pubs the owner sometimes sets up a WiFi network that their patrons can connect to, however most people have to provide their own.

to get to the internet , you will need.

A broadband connection (ADSL / Cable) this normally comes with a standard NON wifi modem
A WiFi Router (including ADSL / Cable Modem) depending on what you have already.


then to link a remote PC / Laptop to this network, A suitable wireless adapter ( like your belkin adapter)

it is a common misconception that a wireless adapter is all you need (advertising is vague)

Do a hard reset,usually there is a button on the back of the router.With power plugged in,press and hold reset button 15 sec. then without releasing button remove power plug and hold an additional 15 sec.,then plug power cord back in and hold an additional 15 sec. After that release the reset button and it should reset to default.You may need to do this a few times but it should solve your issue.

Using the reset button The location of your range extender's reset button will vary depending on its model. The reset begins once you press and hold thereset button for at least 10 seconds while the range extender is powered ON. The Status Light on the the range extender will momentarily flash and will then begin to blink. When the light becomes solid again, the reset is complete. Using the web-based setup page If using the physical button does not work, you can access the range extender's web-based setup page and do the reset from there. Before you begin:

• Make sure that the wireless computer or device you're using to access the web-based setup page is connected to the same network as the range extender.
• You need to identify the IP address that your router has assigned to your range extender. Locate this by accessing your router's DHCP Client table. Once you have the range extender's assigned IP address, use it to access your range extender's web-based setup page.
• Alternatively, you can enter "http://192.168.206.1" in the web browser's Address bar if your range extender has NOT detected a DHCP server in your network.

Step 1: In the web-based setup page of the range extender, go to Utilities and select Restore Factory Defaults. QUICK TIP: You may be prompted to log in with your range extender's administrator password. If you have not set any, simply leave the field blank and click on Submit. Step 2: Click on the Restore Factory Defaults button. Your Belkin range extender should now be restored to its factory default settings.

Routers are very important for setting up an internet connection. As we all know, the Internet is the most important network, which connects us to the world. There are various companies exist in the market, which offers routers. But Belkin is the top market-leading company for routers. Advance features, technology is the attributes of the Belkin router. For a new router user, installation is a big challenge, and in case the user doesn't.have installation CD then it becomes more difficult. So in this blog, we are going to discussHow to Setup Belkin Router Without CD. Now, you do not need to worry about the installation process, There are 2-3 ways to set up Belkin Router Without a CD.Now one question comes to your mind, How? So Tech Support Experts are here to answer all your queries. Our team is experts in technology and here we will elaborate on the steps to Setup Belkin Router Without CD.

Scroll down and select your Belkin device's setup utility. This varies by product, but begins with "Belkin" followed by your device type. Click "Uninstall" and enter your Windows administrator password if prompted. Click "OK" to confirm that you wish to uninstall.

How to Uninstall a Belkin Utility