20 Most Recent
Frigidaire GLEQ2152ES Electric Dryer - Page 2 Questions & Answers
Why is dryer get very on on top of outside of dryer
SOUNDS LIKE THE BLOWER ELEMENT IS NOT FUNCTIONING PROPERLY DUE TO RESTRICTIONS? CHECK UR VENTING? AND LINT BASKET IF ITS FULL UR INSIDE OF UNIT MAY BE FULL OF LINT ALSO BAD BAD AND BAD CAUSES OVERHEATING AND THEN SHUT DOWN?
Error "AD" when drying
thats not an error code error codes are f codes eg. f01 f02 thats a cycle code for auto dry are you having any promblems other than the display
Does not heat
BAD HEATING ELEMENT. I believe that particular model has a ring type heater coil; very effective but fragile. The dryer must be disassembled until you see the entire heater coil, I've attached a photo. The replacement is less than $80 via Amazon Prime, I know, I've done this. The kicker is that the coil was still putting out a little heat but taking forever to dry. You're just asking for a fire or a total breakdown which could adversely affect your control board (not cheap).
Dryer runs when door is closed and not programmed
Control board malfunction. Leave it unplugged for a few minutes to reset the board, plug it back in and look for error codes. If none, and it still runs without programming, it could actually be a faulty door switch; providing erroneous feedback (a loop) to the control board. On a good day, it would be the $5 door switch or a dusty light bulb fixture (which is in series with the door switch). Here's hoping for the best, good luck.
Why does my FERB7800DS0 Frigidaire dryer has no heat
Good Afternoon Friend,
I understand your Frigidaire dryer, model# FERB7800DS0, is not heating up. Please try resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.
-Best Regards-
WP
Dryer will run but will not heat and the lights all flash
Good Afternoon Friend,
I understand that your Frigidaire dryer, model# GLEQ2152ES, will run for a few minutes and then stop and display "AD" with the lights flashing. The "AD" means that your appliance was in an automatic dry mode. I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.
-Best Regards-
WP
How to install board
Good Morning Friend,
I understand you want to know how to replace the board on your Frigidaire dryer, model# GLEQ2152ES. Typically, this is not a do it yourself repair, as there are no step by step instruction manuals. I suggest contacting your local authorized technician for further assistance. They have been trained on your particular appliance, and should be able to replace the board with ease. Hope this is helpful.
-Best Regards-
WP
Clothes item get caught between drum and dryer cabinet
Good Morning Friend,
I understand that your clothes are getting caught between the drum and the dryer cabinet of your Frigidaire dryer, model# GLEQ2152ES. First, check and make sure that the door is completely closed, so clothes are unable to escape that way. Secondly, check the lint cover and make sure that nothing is escaping that way. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.
-Best Regards-
WP
What is a hard reset?
Good Morning Friend,
I understand you want to know what a hard reset is on your Frigidaire dryer, model# GLEQ2152ES. A hard reset involves you either unplugging your appliance or shutting the power off at your home's circuit breaker, for 3-5 minutes. You will turn the power back on and see if whatever issue has been resolved. Hope this is helpful.
-Best Regards-
WP
Not finding what you are looking for?