20 Most Recent Frigidaire GLEQ2152ES Electric Dryer - Page 6 Questions & Answers

Hi Phil - Based on the symptoms you are describing, you may either have a communication error from the main control board or the timer itself may not be operating correctly. Since you are noticing a humming noise, it could either be a clogged drainage hose or pump that needs to be cleaned, or it could possibly have another issue with the door lock assembly or a damaged tub. I would personally contact a professional to accurately diagnose the washer to determine the root cause to reduce the risk of unnecessary parts.

Check if you soldered it correctly, if not, the relay might have been damaged, you might need a new one

Hi Mary - You may try reprogramming the dryer by disconnecting the power to the unit. This can be done by either unplugging it or flipping the household circuit break to the off position. Wait approximately ten minutes and turn the unit back on. If the issue persists, then the dryer could possibly be experiencing a communication with the control board, a potential wiring failure, power source or a faulty door lock assembly. Because it could be a number of any one of several underlying causes, I would recommend contacting a professional to properly diagnose and repair the appliance.

First thing is to check that your dryer is venting properly. If it is restricted this may occur. There are vent cleaning kits that you can purchase to make it easy to clear your vent from the rear of the dryer to the outside exhaust. Check were your link screen slides in at and inspect it for excess link build up. Any more questions you can contact us a dryer repair service.

Probably the bearing drum support part# 131825900 or th drum glides 2x 137513300.

I am not sure you have one, if you have one, should be around the electric panel

This is fairly easy. You will notice a number of sheet metal screws located just under the top when you remove the back of the dryer. They will be attached to another stationary part of the dryer. Sometimes the top is slid into place and will come off by sliding it forward and then lifting up. I am assuming you are replacing the element or the relay switch.

Hello dneal66 - Generally qualified technicians often perform complicated part replacement such as this due to liability and safety reasons. If I was in your position, I personally recommend contacting a professional to accurately diagnosis the precise issue before investing in parts that may or may not be the root cause. You can often locate a certified service provider through the manufacturer website.

Hello Tonya Reyes - Try reprogramming the dryer by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes, restart unit and select a normal cycle. If it proves to be ineffective, I suggest cleaning the lint screen/filter. Also check that the power cord is not damaged. Otherwise the dryer may possibly be experiencing more serious issues such as; wiring failure, faulty control board, thermal limiter, or defective door switch. I would strongly recommend contacting a local professional for further diagnosis should all troubleshooting measures fail. You can often locate qualified servicers by visiting the manufacturer directly.

Hola Ivan Salas - La informacion que usted necesita, la puede conseguir aqui.

Hello Yvonne Ramsey - From what you are describing it sounds like it is more than likely due to a broken heating element. The heating element is located directly behind the drum. If a strand of the heater wire contacts the rear of the drum it may create spark or arcing. I strongly suggest consulting a professional to properly diagnosis the unit and move forward accurately with the repairs.

Hello emergsvc - From what you are describing it could be a number of issues that dryer could be experiencing. The unit could possibly have a wiring failure, communication error from the control board, faulty door lock assembly or power supply. I strongly suggest contacting a professional to accurately diagnosis the unit and to properly assist with the repairs.

Hello Brenda Gibson - Try reprogramming the unit by flipping the household circuit breaker off or unplugging it. Wait approximately ten minutes and restart unit. If it proves to be ineffective, the dryer could possibly be experiencing a communication error with the main control board, wiring failure, or faulty door lock assembly. Consult a professional for an accurate diagnosis and to assist with the repairs.

Hi cory_pettifo - Try reprogramming the dryer by flipping the household circuit breaker off or by unplugging it. Wait approximately ten minutes and restart unit. If it proves to be ineffective, then typically this is something that a professional would need to accurately diagnosis. Unit could possibly have a faulty power cord, house wiring, faulty control board, thermal limiter or door switch.

Sounds like something became wedged against the drum. Maybe a bearing?

Hi and welcome to FixYa, I am Kelly
Sorry to keep you waiting. I just now saw your post.

The installation instructions with dimensions is here: (2.94 mb)

http://manuals.frigidaire.com/prodinfo_pdf/Webster/134917700es.pdf
(^-See page 6)

Owners manual:
http://manuals.frigidaire.com/prodinfo_pdf/Webster/134763300een.pdf

Wiring Diagram:
http://manuals.frigidaire.com/prodinfo_pdf/Webster/134509400efs.pdf

Firgidaire manuals if the above is not the correct model:
http://www.frigidaire.com/manuals Enter your model number and all of the manuals for the model number you entered (like above manuals) will be availble for download.

Thanks for choosing FixYa,
Kelly