20 Most Recent
Disney 13" TV - Page 5 Questions & Answers
Discs will not play
Could be a number of things:
1. The disc is dirty. Remove and clean with soft cloth. Remove fingerprints and smudges.
2. The disc is scratched. Remove disc, clean and try to repair with a CD scratch removal kit.
3. The disc is flawed. Remove, throw away and replace disc.
4. The camera laser is dirty. Clear debris from laser with canned air. Do not touch laser.
5. The laser is out of alignment. Professionally repair or replace camera.
In need to open the lightning mcqueen 13 inch tv to plug in cord
there are five plastic nuts on each wheel. three of these nuts have screws under them. i took some small pliers apllied slight pressure and wiggled the black plastic nuts off. be careful while doing this because you can break the clips on the nuts. Wont create a problem but if your careful enough the plastic nuts will come off without breaking anything. i just thought i would mention that. After you get the wheels off there will be about 6 more screws to remove 4 black screws and 2 silver screws. Good luck!
Hooking up dvd player
Look for any button either on the unit or the remote marked with common stuff like A/V, Input, Source, Aux or Au, Line, TV-VID. or try dialing in Channel 0, or 00, or 1, or Channel Down surf below Channel 2. Alternately, get into the menu and look for stuff concerning Auxiliary inputs.
If all else fails, you can run a DVD's audio and video line-signals THROUGH a VCR. Hookup the VCR to the TV's RF (threaded) connector using standard coaxial cable. Hookup the DVD a/v output lines to the Line-ins of the VCR. Tune the TV to Ch. 3, tune the VCR to Line-in or Auxiliary and press the play or tv/vid button on the VCR to force the DVD signal through on channel 3 onto the TV.
Disney 13' Princess tv
You've tried all the codes for your TV, but you still cannot get the remote control to operate your TV.
- Turn on your TV.
- On the remote control, press TV once.
- Then press and hold SETUP until the TV key blinks twice, then release the SETUP key.
- Using the number pad, enter 9-9-1. The TV key will blink twice.
- Aim the remote control at the TV and slowly alternate between pressing Power and TV. Stop when the TV turns off after pressing the POWER key. This means that a working code has been found.
- Press the SETUP key once to lock in the code. The TV key will blink twice.
Hope this helps
Remote control
Try the media center remotes. Easily programmable. In fact, contact
www.mediarx.co.uk and they will pre-programme it for you before dispatching for £9.99
Disney tv has a picture but no sound
Common issue with some of the TV sets. If your headphone socket is squeeky clean it is more than likely a manufacturers fault. Please seek a re-fund or contact the manufacturer
Blocked Channels
Look for a reset to default feature in the settings of the TV. That should release the unblock feature and should pick up all channels during the scan.
Has sound but no picture
if you know how solder.then re solder your tv first. then,check the vertical section maybe the ic is busted
JVC TV
need model number fo say anything about it
Broke remote
Buy a new replacement universal remote from walmart for about 6 bucks.
Digital TV Stations
The term digital in this case is the mechanism used to tune in stations. Rather than making adjustments using a front dial to fine tune the stations, there are digital circuits that will lock in the station. The "digital" stations you are referring to now are the over-air digital broadcasts what use a different method for transfering the signals over the air. These stations now broadcast a digital stream of information rather than an analogue TV signal. If you are using an antenna for receiving these over-air broadcasts, you will require a converter.
Dan
Disney dvd player P600D
hi,
I have a high end sony universal remote that will let you program a sequence of command keys like doing it manually, this remote has a blue backlit touch keypad I lucked out and found it at a thrift store, its a godsend. we only have to hit 1 key Maybe talk to a rep at circuit city and tell him you want a universal remote where you can program the sequence, thats all I have sorry
J
I can not get the tv to switch over to the dvd
On the tv remote there is a button that says input. Hit this button and a list of different items comes up. Continue to hit the input button until you get to the one on the list that says AV. Once you have it set to AV, your dvd should play.
Not finding what you are looking for?