GE 28111 Cordless Phone - Page 2 - Answered Questions & Fixed issues
Blinking blue light
Press the mute/program button, then press the caller ID-volume button to select handset setup. Next press caller ID-volume until you get to Default settings. Use the caller ID-volume button to select 1yes. This will return the phone to the factory settings and for took care of the blinking blue light, however you will loose any custom setting or numbers you entered.
5/27/2008 12:39:07 AM •
GE 28111...
•
Answered
on May 27, 2008
•
435 views
When someone calls the buttons flash but doesn't ring.
Your ringer has been switched off..to solve this press the menu button(mute in most of the sets)and press it until you see the option ringer press + to change it to off and then press menu again until you see the main screen...Thats all..
Let me know if it worked..
12/18/2007 10:24:29 PM •
GE 28111...
•
Answered
on Dec 18, 2007
•
230 views
GE 28111 Twin Cordless Phone "Line In Use"
I had the same problem. I went to each handset and pushed the talk button. After I got a dial tone, I pushed it again to stop the dial tone. The message went away.
12/10/2007 4:14:44 PM •
GE 28111...
•
Answered
on Dec 10, 2007
•
1,562 views
Validation
I would assume this could have been a product that was returned to the company that you purchased it from. Follow these instructions.
1. 1. Disconnect power from the base by pulling the plug out of the back of the unit.
2. Press and hold the Page button and while holding the Page button reconnect the power.
3. Continue to hold the Page button until the charge/in use light flashes rapidly.
4. Release the Page button.
5. Press and release the page button on the base once. All handsets are de-registered and
HANDSET NEEDS REGISTRATION shows in the display.
Then
From the Handset Setup Menu:
1. Press the caller ID-volume ( 6 or 5) button to scroll to the REGISTRATION sub-menu.
2. Press the mute/program button to enter the menu. REGISTRATION 1YES 42NO - - -shows
in the display. The default setting is 2NO.
3. Use the touch-tone pad to select 1 for YES or 2 for NO. Or use the caller ID-volume ( 6 or
5) button to scroll to 1YES or 2NO.
4. If you select YES, press the mute/program button. HOLD BASE PAGE FOR 5 SECONDS, THEN
PRESS HANDSET PROGRAM shows in the display. (Your handset should be held near the
base during registration process.)
5. Press and hold the page button on the base unit until the charge/in use indicator flashes.
Press the handset mute/program button. REGISTERING shows in the display. HANDSET X
REGISTERED shows in the handset display, where X is the handset number. You may now
rename your handset. (Refer to Step 3 & 4 of Handset Name Section)
NOTE: IF you are re-registering the handset through the handset menu;
to rename your handset you must go to the Handset Name Section and
start from the beginning step.
I understand that you have tried the registation process. Sometimes with electronics, you have to start from ground 0, before it will work correct again.
If there are further questions or comments, please post here.
Please rate this solutn through fix-it.
Thank you
7/8/2007 10:09:53 PM •
GE 28111...
•
Answered
on Jul 08, 2007
•
235 views
I have a GE model #29893GE1-B it is connected and plugged in, but no dial tone
Remove all the phones on the system. Remove all the handset batteries. Plug in one old style corded phone to the main phone jack, it is normally the one closest to the front door. Do you have dial tone? If not, it is your Telco. If you have a dial tone, plug all the other phones in testing for a dial tone as you go.
1/27/2023 7:06:13 PM •
GE Lands Phones
•
Answered
on Jan 27, 2023
•
52 views
Why is my GE washer leaking water from the right front corner?
A leak coming from the front of a front-load washer is often caused by a damaged or dirty door seal. If the door seal is cracked or loose, it will need to be replaced in order to restore a watertight seal. Always ensure all clothes pockets are empty prior to washing, as objects left in pockets can damage the door seal.
11/25/2022 12:51:11 PM •
GE Lands Phones
•
Answered
on Nov 25, 2022
•
50 views
Trying to find replacement phone battery for GE model 2-9421A phone set s/n 80052268.
If you mean the long-life lithium backup battery for the corded 2-line GE 2-9421 (A indicating the sales region), that is a 3V Lithium battery. The part number 5-1923 appears to be a common CR2032 coin cell battery. These are used as backup batteries for Eraseable Programmable ROM on many devices, including computers.. One source is https://www.batteriesdirect.com/product/details/button-cell-batteries/ge/5-1923 . Any CR2032 from a reputable manufacturer will work.
I hope this helps.
Cindy Wells
6/3/2021 9:56:07 PM •
GE Lands Phones
•
Answered
on Jun 03, 2021
•
110 views
Not finding what you are looking for?