20 Most Recent D-Link RangeBooster G WBR-2310 Wireless Router (WBR2310) - Page 2 Questions & Answers

Can i have more info.Channel is related to the router itself not the printer.The channel is acquire by the router automatically.In order to cahnge it you need to access the router configuration.

You will have to set-up using your router. Please use the following source: http://www.wikihow.com/Setup-D-Link-WBR-2310-Wireless-Router hope this helps and please don't forget to rate.

See section 3 page 15 of the user manual.

Available here:

http://www.netwood.net/support/manuals/D-Link_WBR2310_manual_10.pdf

I'm pretty sure that downgrading the firmware to 1.0.3 will work. I had been running at this level for quite some time and for some reason I decided to upgrade to the latest version which started the problems for me. I am downgrading to this now and I expect better results. All of the firmware versions are available at http://www.dlink.com/products/support.asp?pid=470&sec=0. You pick the right hardware revision. PLEASE NOTE: Save off/remember your settings as when you change the firmware it resets all of them back to system defaults.

http://www.netwood.net/support/manuals/D-Link_WBR2310_manual_10.pdf

Use the On-Line setup. User setup manual: http://www.netwood.net/support/manuals/D-Link_WBR2310_manual_10.pdf

This may help: http://www.dlink.com/us/en/support/product/wbr-2310-rangebooster-g-router

If the default password on the D-Link has been changed then-To reset the D-Link back to the default settings -Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button. (firmware version was 3.00, and upgraded to3.05)Connect a LAN cable from the D-Link to your laptop/computer'sLAN port, open the browser on your laptop/computer and enter the D-Link's configurationURL..http://192.168.0.1The default login = adminThe default PW = blank (just press Enter)You can now change the default admin password.You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

Network Key (WEP, WPA, WPA2 Encryption key)To connectyour computer to a wireless router, you click the Refresh networklist, then Choose your wireless network and then click Connectto your secured Wireless Network, it will asks for a Network Keybefore allowing you to connect into your wireless network. This NetworkKey is either the WEP, or WPA or WPA2 Encryption key that is used toconfigure the Wireless Router. The Passphrase is an alternate way tosetup the Encryption key.When you are requested for a Network Key, you can just enter the Passphrasethat was used to configure the Encryption key in the wireless router.http://www.fixya.com/support/r5270415-network_password_network_addressFor information on securing your wireless network,configuring the wireless router and configuring the wireless card in thelaptop/computer, please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

WiFi BoosterA wireless USBInternet adapter with a 54Mbps 802.11Gadapter with a powerful antenna,From WorldStart, please click on this link totheir WEB site:- http://store.worldstart.com/product/5412Boost Wireless Network - 2.4GHz DipoleMIMO (multi-input, multi-output) antenna http://www.jaycar.com.au/productView.asp?ID=AR3280http://www.alibaba.com/product/tw103028965-103211250-100674400/MIMO_ANTENNA.html

hey,

There are a number of reasons for this.

1. try to move your router to the center of the room. If it is placed in a corner this could happen.
2. If there are multiple routers at home, then this could happen.
3. Try to login to the router page and try to change the signal strengths and channels.
4. This could also happen due to the type of encryption you have chosen. try to disable wireless encryption and if the disconnect does not happen, then try different combination of encryption until you get the desired result.

Cheers!!!

sir connect the router using lan cable to computer and open the web browser and type the IP of your router i.e 192.168.0.100 , and type admin as user name and in password also type admin then go to security option there and replace the security code whatever you want.. Thanks.

This change happens in the ROUTER and not the PC. You will need to log in to the router and invoke wireless security. You can get the exact procedure from D-Links web site.

Hi. Let's hava look at what you are doing. I'm guessing that you have a cable modem a dlink router with wifi and a computer, right? If you connect the cable modem to the computer you have internet. You shouild also have wfi but the wifi will not give you internet because it is disconnected from the modem. The Dlink has to be connected to the modem but it will also need to be configured. To *** that you will need help from your cable company. The connections should be. Modem connected to the outside world. Dlink connected to the Modem. Computer connected to the Dlink by either wifi or Ethernet.

You normally have to use the router's web user interface, then find the upgrade feature, which will prompt for the file. But if you cannot get to the web user interface of the router, then you may be out of luck for upgrading the firmware,