Konica Minolta Minolta Bizhub C253 Copier - Answered Questions & Fixed issues

When you open the right side door and look down at it you see a sponge looking roller. That is called Second transfer roller. The paper will go between that roller and transfer belt the shinney belt inside the machine it aligns with. During operation the roller should retract. There is a senor and motor that work together to execute the procedure. You will have to remove the assy. to get to the motor and sensor if its not them its the main board serious buckets and I doubt you can get one.

https://printcopy.info/?mod=erc&brand=Konica-Minolta&model=bizhub+C253&code=C2152

You take a picture of the device's screen.

remove all of the image units, shake each one so as to have the developer in each unit be spread out along the entire unit not at one end, after doing that to each one install them properly. open close front door to clear code if it come back if these image units are third party get real Konicaminolta units and get a tech out Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace it Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the image unit Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

try this site Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the yellow and magenta image units Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the black image unit Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

DID Some one recently replace a color image unit? Was that image unit stored standing up? and placed directly into the machine.? Might have all the developer sitting at one end and motor can not turn. Pull out all the image units, shake each one along the axis of the unit to spread the developer over the entire length of each image unit, then re-install, open close front door to reset code, if the code comes back you might have a burn out color image motor, or on of the color image unit needs to be replaced replace all three, worse case the board that controls the motor was damaged. Store all Image units and toner length wise Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Polygon Motor for the Black Print head LASER is bad, the motor is internal to the print head get a new print head for the black, requires tech to install, clear code bye open closing front door. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Replace the black drum and black developer unit P-9 Black drum issue and P21 registration issue since black is used as the reference for registration of colors can see a P-9 and P-21 code combo. Precision Roller Printer Toner Cartridges Parts and Supplies Office... Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

what is the question? ------------------------------------------------------------------- Drum, Transfer Belt and Fusing Unit Firmware Reset - http://www.bizhubreset.com Drum and Toner Chip Reset - http://www.chipreset.eu Transfer Belt and Fusing Unit Reset Kit - http://www.resetkit.eu Konica Minolta Error Codes & Solutions - http://www.kmcodes.com

If you have a Fiery rip fitted to the machine then the standard network settings in the admin menu will not be there. you need to click on the (i) icon on the front screen of the copier and this will open the fiery menu. from there you can select print pages>config page and find all the details you need. hope this helps

try to go to your printers and faxes it is located in the start menu.

Enter in the service mode and select tes mode select gradation test pattern and make a test for black,cyan,magenta and yellow.If the gradation is not OK you have change the bad imaging unit,or change the developer and drum in the bad image unit + the chip.

Podtermistor wa?ka utrwalaj?cego nie wykrywa wymaganej temperatury w ci?gu 30 sekund. po rozpocz?ciu cyklu rozgrzewania; dlatego kopiarka nie ko?czy cyklu nagrzewania. • Temperatura wa?k?w utrwalaj?cych nie osi?ga wymaganego poziomu nawet po up?ywie ustawionego czasu podczas cyklu nagrzewania. 1 Sprawd?, czy lampka utrwalacza H1 zapala si?, gdy g??wny wy??cznik zasilania jest ustawiony w pozycji W?., w razie potrzeby popraw lub wymie?. - - 2 Sprawd?, czy H2 w??cza si?, gdy g??wny wy??cznik zasilania jest ustawiony w pozycji ON, i w razie potrzeby popraw lub wymie?. - - 3 Sprawd? instalacj? TH1 i TH2 i w razie potrzeby popraw lub wyczy??. - - 4 Sprawd? dzia?anie TH1. Usu? CN80 (4P), a nast?pnie sprawd?, czy rezystancja na CN80-2 i -3 na termistorze jest niesko?czona. - - 5 Sprawd? dzia?anie TH2. Usu? CN81 (4P), a nast?pnie sprawd?, czy rezystancja mi?dzy CN81-2 i -3 na termistorze jest niesko?czona. - - 6 Sprawd? ci?g?o?? H1. W razie potrzeby popraw lub wymie?. - - 7 Sprawd? ci?g?o?? H2. W razie potrzeby popraw lub wymie?. - - 8 Zmie? PU1 - - 9 Zmie? PWB-A

Replace the Black drum and developer unit (P9) (P16) and clean the IDC forward sensor(P5) (Requires removing the Transfer belt) L4 Black Drum Rotation well passed its life.

English only on Fixya please. We are a North American website.

Error Code Pls help - Konica Minolta

Copytechnet https://www.copytechnet.com > ... > Konica Minolta Jun 20, 2012 - CD252 (C-D252) code at start up. Solution CAUSE: The Controller 1 setting is enabled in Tech. Rep. Mode without the IC-409 (Fiery® ... fuser error code C252 May 7, 2014 Bizhub C451 bad print quality, no accurate color Jun 4, 2014 Error Code Bizhub 283 with C-D272 Mar 17, 2016 error code C- D251 bizhub C451 May 19, 2009 More results from www.copytechnet.com

Konica-Minolta bizhub C452 - Error Code

Printcopy.info https://printcopy.info > model=bizhub+C452 Code: CD252; Description: No relay circuit boards for IC-412 mounting at IC-412 mount setting; Causes: MFP board (MFPB) Relay circuit boards (VI-505) . ..

C454 and C454e firmware - Page 2

Copytechnet https://www.copytechnet.com > ... > Konica Minolta May 4, 2019 - Re: C454 and C454e firmware. Hi there, I hava Konica Minolta Bizhub C454 with ROM Version: b-IZHUB-c454 - imgbb.com C454 and C454e firmware May 5, 2019 UPDATE FIRMWARE ON c454 Jun 19, 2015 Bizhub latest firmware? Mar 10, 2022 Firmware question Jun 19, 2019 More results from www.copytechnet.com

Updating the Firmware of This Machine

Konica Minolta Manuals https://manuals.konicaminolta.eu > contents User's Guide. bizhub C554 C454 C364 C284 C224 ... A firmware for this machine can be downloaded from the Internet to update the machine firmware.

Download Center - KONICA MINOLTA

konicaminolta.ge https://www.konicaminolta.ge > download-centre The download center of Konica Minolta! Find everything from driver to manuals of all of our bizhub or accurio products.