Durabrand DWT2405 24" TV - Answered Questions & Fixed issues
I am trying to hook
need rca ---wires yellow, white, red -- match the output of the DVD player to the inputs of the tv, or have one the kids do it for you.
3/16/2011 2:13:17 AM •
Durabrand...
•
Answered
on Mar 16, 2011
•
180 views
The tv does not turn on when I push the power
Hello,
The issue you describe is consistent with a power supply board issue. This is the board where the AC goes to. This problem may have occurred as a result of irregular power supply, or excess power supply or power surge.
The TV is receiving current but cannot circulate or transfer the current to other necessary part of the TV because of the defective power supply board.
I do not think it needs replacement, rather some defective capacitors are causing this issue.
Open unit up and take a look at the power supply board.You will probably see one or more electrolytic filter capacitors that are bulged up in the top-not perfectly flat like the others.
The value of these capacitors will be different, most likely they will be somewhere around-820 to 2200uF/25 V( or /10V sometimes)
You can replace them with same values but I would recommend the voltage rating to be higher(like 35V for an original 25V) for reliability purposes.
What happens is,these bulged top capacitors will cause a low and unfiltered DC voltage=main board will malfunction(the relay will keep clicking until the caps are holding enough charge to bring the voltage up over a threshold point).
You can buy these capacitors at any Fry's or Radioshack store or you can order them online at vendors like "mcmelectronics.com"(look for electrolytic capacitors).
After replacing these capacitor(capacitors) most likely the normal operation will be restored.
Note: There may be also some other causes for this symptom ,like a defective T con board ,or main board,but the bulged top capacitors are the most common cause for this issue.
If you don't know about TV repairers, take the TV to the nearest repairman to fix the fault for you. Also, note that TV stores a lot of current, so wait a while before opening the TV back cover.
I hope this helps.
Good luck.
3/2/2011 7:56:47 AM •
Durabrand...
•
Answered
on Mar 02, 2011
•
93 views
I have basic Cable service,
Hello
Just check its cable connections at its rear socket for tightness. If it is alright, put the set to auto tune, and let it tune all the avialable channels from the cable at that time and store it automatically. This may take 2 or 3 minutes. Wait till then and check for clarity. If the result is same as previous, the tuner inside your TV is faulty, and should be replaced with same type and number. OK.
2/17/2011 4:37:12 AM •
Durabrand...
•
Answered
on Feb 17, 2011
•
190 views
I just got a used
I hope that you have gotten this resolved, but if not, here are some simple steps to try! If you are at TV1, where the receiver box is located, the tv needs to be on channel 3 or 4. Depending on the cable that is running between the receiver and the tv, the tv may need to be on an input, such as video 1 or 2. If you are at the TV2 location, where there is no receiver, then the tv needs to be on channel 60 or 73. I hope this information helps!
Becki Barned
DISH Network Customer Service
2/2/2011 3:15:51 AM •
Durabrand...
•
Answered
on Feb 02, 2011
•
113 views
Tv is stock on tv
You need the remote to change to game mode. The original remote doesn't appear to be available. A substitute remote with the function is here:
http://www.remotes.com/remotes/servlet/rs?a=Search&o=c&uid=0&m=DWT2405&uuid=12931247714820 . The Game button switches to and from game mode. Other universal remotes may work but a source or input button is needed. Then try various codes for either Durabrand or Funai TVs (Funai built the TV). The other issue is that the remote needs to have been programmed at least 6 months after the TV was released. The remotes that are programmed via a USB connection to a computer will definately be able to match the function.
I hope this helps.
Cindy Wells
12/23/2010 5:25:14 PM •
Durabrand...
•
Answered
on Dec 23, 2010
•
200 views
HELLO!.. I HAVE A DURABRAND TV. AND I HAVE NEED
Hello
You just buy one Philips CL 034 model Universal remote control, which can be programmed with your Duraband TV. The porgramme codes are
0520 0115 0317
0916 0027 0447 0323
Direct Code Entry
1. Press and hold the CODE SEARCH
button until the red indicator stays
on, then release the CODE SEARCH
button.
2. Press and release the desired Mode
button (TV, VCR, etc.). The red
indicator blinks, then stays lit.
3. Enter the 4 digit code from the code
tables. Note: after a valid code entry,
the red indicator turns off. For an
invalid code, the red indicator
flashes.
4. With your device on, press
CHANNEL UP. If the device
responds, no further programming is
required. Note: If some buttons do
not operate your device, try one othe other codes for your brand.
Ok
11/27/2010 1:41:14 PM •
Durabrand...
•
Answered
on Nov 27, 2010
•
115 views
MY MOM HAS A DURABRAND
buy a unaversal remote, program it to her tv and try taking care of the issue that way
8/21/2010 1:33:42 AM •
Durabrand...
•
Answered
on Aug 21, 2010
•
69 views
I was given a duro
Do you mean no power or no cable?If you mean no cable,did you do a channel autosearch?Is it new or used?Even if it is 5 years old,an autosearch should pick up some digital channels.If it does not have the original remote,you will have to use the menu button on the TV to access the channel search.If none of these options work,it is simply a large paperweight.Universal remotes do not give menu access.Let me know how you make out.Just make a comment to this post and I will get a notice that you replied. Good luck! Greg
8/16/2010 5:24:31 AM •
Durabrand...
•
Answered
on Aug 16, 2010
•
96 views
Tv stuck on aux
No, there is only the remote option for this TV.
7/17/2010 7:42:54 PM •
Durabrand...
•
Answered
on Jul 17, 2010
•
465 views
Hooking up a dvd player
Red and white are audio cables
Yellow is video.
Your problem is that your TV has no video inputs. TVs use those red white and yellow plugs to transmit the signal via those cables.
By cable box - do you mean a digital box? You can't run it through that unforunately - those connections are only for the box itself and it only has an output.
You'll have to go either:
Buy a new TV
or get an RCA Modulator.
7/4/2010 9:22:27 PM •
Durabrand...
•
Answered
on Jul 04, 2010
•
254 views
Not finding what you are looking for?