Top 20 Durabrand DWT2405 24" TV Questions & Answers

DURABRAND Replacement Remote Control for DWT1304 NE142UD DWT2405 DCT1304R... http://www.instructionsheets.com/mfg/d/durabrand/pdfs/dct2405r.pdf

Check whether the audio is muted by accidental press at remote control button. Enter its sound menu, and check it. If muted, as you know there will be no audio output. If not muted, check the speaker/s. If found OK; check and replace the damaged component/s at its audio output section circuit board. If needy, replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ http://electro-medical.blogspot.com/

Check and replace its main power supply regulator board as card basis. Contact any service technician. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" will make surf easy. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/

Check its speaker. If it is found OK, the audio output section circuit inside have the fault.

Hello
Just check its cable connections at its rear socket for tightness. If it is alright, put the set to auto tune, and let it tune all the avialable channels from the cable at that time and store it automatically. This may take 2 or 3 minutes. Wait till then and check for clarity. If the result is same as previous, the tuner inside your TV is faulty, and should be replaced with same type and number. OK.

Hello,

The issue you describe is consistent with a power supply board issue. This is the board where the AC goes to. This problem may have occurred as a result of irregular power supply, or excess power supply or power surge.

The TV is receiving current but cannot circulate or transfer the current to other necessary part of the TV because of the defective power supply board.

I do not think it needs replacement, rather some defective capacitors are causing this issue.
Open unit up and take a look at the power supply board.You will probably see one or more electrolytic filter capacitors that are bulged up in the top-not perfectly flat like the others.

The value of these capacitors will be different, most likely they will be somewhere around-820 to 2200uF/25 V( or /10V sometimes)

You can replace them with same values but I would recommend the voltage rating to be higher(like 35V for an original 25V) for reliability purposes.

What happens is,these bulged top capacitors will cause a low and unfiltered DC voltage=main board will malfunction(the relay will keep clicking until the caps are holding enough charge to bring the voltage up over a threshold point).

You can buy these capacitors at any Fry's or Radioshack store or you can order them online at vendors like "mcmelectronics.com"(look for electrolytic capacitors).
After replacing these capacitor(capacitors) most likely the normal operation will be restored.

Note: There may be also some other causes for this symptom ,like a defective T con board ,or main board,but the bulged top capacitors are the most common cause for this issue.

If you don't know about TV repairers, take the TV to the nearest repairman to fix the fault for you. Also, note that TV stores a lot of current, so wait a while before opening the TV back cover.

I hope this helps.

Good luck.

You need the remote to change to game mode. The original remote doesn't appear to be available. A substitute remote with the function is here: http://www.remotes.com/remotes/servlet/rs?a=Search&o=c&uid=0&m=DWT2405&uuid=12931247714820 . The Game button switches to and from game mode. Other universal remotes may work but a source or input button is needed. Then try various codes for either Durabrand or Funai TVs (Funai built the TV). The other issue is that the remote needs to have been programmed at least 6 months after the TV was released. The remotes that are programmed via a USB connection to a computer will definately be able to match the function.

I hope this helps.

Cindy Wells

need rca ---wires yellow, white, red -- match the output of the DVD player to the inputs of the tv, or have one the kids do it for you.

Hello
I don't understand your language. Will you please give me some words in English language, about the probelem you are facing with your Duraband Tv; please.

Hello You just buy one Philips CL 034 model Universal remote control, which can be programmed with your Duraband TV. The porgramme codes are
0520 0115 0317 0916 0027 0447 0323
Direct Code Entry 1. Press and hold the CODE SEARCH button until the red indicator stays on, then release the CODE SEARCH button. 2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit. 3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes. 4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one othe other codes for your brand. Ok

ago to philips.com - customer support, or try retrevo.com to download remote manual;

Most are factory set for all zero's to start with or 1 2 3 4

plug off the cord, restart it and from the panel button, press the several times menu button until video comes up.

I hope that you have gotten this resolved, but if not, here are some simple steps to try! If you are at TV1, where the receiver box is located, the tv needs to be on channel 3 or 4. Depending on the cable that is running between the receiver and the tv, the tv may need to be on an input, such as video 1 or 2. If you are at the TV2 location, where there is no receiver, then the tv needs to be on channel 60 or 73. I hope this information helps!


Becki Barned
DISH Network Customer Service

No, there is only the remote option for this TV.

Do you mean no power or no cable?If you mean no cable,did you do a channel autosearch?Is it new or used?Even if it is 5 years old,an autosearch should pick up some digital channels.If it does not have the original remote,you will have to use the menu button on the TV to access the channel search.If none of these options work,it is simply a large paperweight.Universal remotes do not give menu access.Let me know how you make out.Just make a comment to this post and I will get a notice that you replied. Good luck! Greg

buy a unaversal remote, program it to her tv and try taking care of the issue that way

Thats probably an issue with your power supply. call or click below for the service manager at 303-770-6321

Durabrand TV Repair Denver at AAAA

Try R/C from wallis I found they can do every thing and they have a fantastic after sales service. Jus to try go to www.sosremotes.com select eg. cm104 and see if your tv model is in their database.

Hi there,

Here is a list of codes that might work for your TV:
0054
053
20039
10463
10180
10178
10171
11034
02
25
58
520
115

Thank you for using FixYa! Have a nice day and please remember to rate this solution.

Warm regards,
BearWeb