20 Most Recent Hotpoint Ultima WF860 Front Load Washer - Page 8 Questions & Answers

There are few methods, depends on the age of the appliance.

Press the Start/Cancel button until all the console LED's illuminate. Press both Start/Cancel and On/Off buttons together until d OFF appears. The default screen returns and you can select a new programme.

Simply press the Cancel button and the appliance returns to default. Press On/Off and Start/Cancel toghether with top left option button until d OF appears.

or

Switch off at mains, press and hold On/Off & Start/Cancel buttons, switch mains back on, keep holding down buttons until Doff appears in display.

Check the filter and the actual pump itself for blockage.unless you have already done so, also pump itself could be faulty.

what type of soap are you using make sure its for front load washers.

Hi,

F10 is a pressure switch not sensing error. Basically its a filling problem.
What you need to do is make sure the fill hose isn't kinked up at the back stopping it from filling fast enough.

If the hose is OK then take off the fill hose and aim it into a bucket and turn the water tap on. Then from there see what the water pressure is like there.

If its weak then you need the water pressure sorting out.

If the pressure is fine then you will need a multimeter and test the water valves on top and see if any of them are faulty.

But the F10 error code is a filling issue.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

What is the model number list on the door jamb?

go to instru.manual section troubleshooting and fix it. God bless youif doesnot have it download from www.fitness.manualsonline.comHowever try this.The processes below will get most controls unlocked. Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 15 seconds. Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 15 seconds. Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 15 seconds. Some Models- Press and hold the control lock button for 15 seconds. If none of these work try unplugging for 5 minutes

has it got a filter if so should be around the kick plate under the door if there is no door some hotpoints have a 1 just indide the door at the top if still no you havent got one

The F4 error indicates that the .

This normally indicates a problem with the pump. Usually it is blocked and once cleared the error condition will also clear.

Do the following.

1. Switch off the machine, unplug or disconnect the mains power to the machine and turn off the water supply to the machine.
2. Remove the filter and make sure that the filter is not blocked and is clean and clear of all debris. Clean as required. Note that if the machine has stopped and not fully drained then you may be able to drain out the excess water by removing or disconnecting the waste hose and laying it on the ground in a tray. It may take a few minutes to empty but it will save a small flood. Alternatively bale out the sump under the main screen filter plate.
3. Proceed by checking the drain hose for proper connection and kinks and make sure that it is not blocked or restricted.
4. Also check that the main waste drain pipe and one way valve to a sink waste connection if you use one, is not blocked and clean if required.
5. Access the pump from under the lower rotor arm and protective grille and check that the impeller is free to move and is not clogged or restricted by debris or sludge. Clean as required.
6. Reconnect the power and switch the machine on.

If the problem persists then do the following. 7. Switch off the machine and disconnect the mains power. It is a good idea to take digital pictures of the pump assembly before attempting to work on it or remove it so that you can refer back to it when you reassemble the unit or replace it with a new unit at a later date / time. 8. Remove and check the electrical connections to the pump and make sure they are in good order. 9. Remove the connecting hoses, and expect water to drain out and make sure the pipes are not blocked with debris or any object blockage. If they are then clean them thoroughly. 10. Then remove the pump and check motor is OK and that the motor turns OK. Also check that the pump impeller vanes are in good order and not blocked. If necessary replace the pump with a new and identical unit. 11. Carefully reassemble the pump observing the correct placement of gaskets, seals, O Rings, hoses and securing straps, electrical wiring. 12. Reconnect the hoses and then reconnect power and switch the machine on.

Hi
my washing machine is 2 years old, hotpoint wt761p showinf f-01. it hasnt finished it cycle. turned off by mains to open the door and get washing out.

please help!!

stella