Top 20 Nordic Track NordicTrack Commercial 1500 Treadmill Questions & Answers


Replacement Parts for Fitness Exercise Equipment at SPORTSMITH

The following link is to a manual for your model. This should provide some insight before disassembling the unit. The most important part is to label the connection wires so that you are sure where they go when you put it back together. Also be considerate of any pinch points so that you do not accidentally pinch or crimp any wires when putting it back together.

249920 NORDICTRACK 1500 TREADMILL SPORTSMITH net

Nordic Track... | 1,442 views | 0 helpful votes


looks like there is power to the board. the board the sends power to the console. there could be a loose connection at the board

Nordic Track... | 608 views | 0 helpful votes


Sounds like a cable harness is undone. The cable feeding the panel which has the computer inside (the power feed) is connected, but the cable from the panel back to the motorized parts isn't. The breakaway is a separate circuit that cuts all power to everything. These are my assumptions (I'm not a nordic track expert), but it's a pretty safe bet, likely the connector in the bottom section. Okay, I just looked it up, first Google "nordictrack 1500 manual" one of the first links is a PDF, with a complete parts breakdown. Depending on your specific model, it looks like there is a connector under the top panel where it meets the right post (and a couple of screws will let you lift it up to check it). It may be partially unplugged, check that first since it looks pretty easy to check.
But I think it's going to be in the bottom, in the bottom of the treadmill the wiring splits to different sections. The motor/incline controller cable (a separate cable #106 on one model I looked up, something like NTL09707 or similar) is probably the one that is either broken or unplugged. So although the computer (up top) is sending signals, they aren't reaching where they need to. Anyway, get that manual, and someone handy with screwdrivers and technology, and they should have it figured out quickly.

Nordic Track... | 442 views | 1 helpful votes


All electronics should have a surge protector. So when the power flickers and send a power surge to electronic plugged into the wall the circuit board is protected like your computer.

Nordic Track... | 281 views | 0 helpful votes


Step 1:

1) test the input voltage motor,if there are the motor need repair,see the diagram attached, and see my personal TIPS for motor help
1_9_2013_6_45_40_pm.jpg

Step 2:

tes the output voltage board, for input voltage motor, if there are NOT the board is faulty, replace see the block d.
God bless you
1_9_2013_6_46_29_pm.gif1_9_2013_6_46_52_pm.png

Nordic Track... | 942 views | 1 helpful votes


Also there may be a problem with the LCB

Nordic Track... | 278 views | 0 helpful votes


Hi Helen,
Where does the sound seem to come from ?

Nordic Track... | 215 views | 0 helpful votes


1) see if the belt is tight or loose, repair or replace the belt

2) test the input voltage motor, if there ARE the motor need repair see my personal TIPS for motor help
3) Test the output voltage board, for input voltage motor, if there are NOT the board is faulyt, replace see the b.diagram attached.
1_9_2013_6_44_05_pm.jpg1_9_2013_6_44_19_pm.gif

Nordic Track... | 147 views | 0 helpful votes


1( tight the ribbon cable and clean it,
2) tight the plug from display board , and clean it.
3) tight the display board vs lower board and clean it unplugged the power
4) test the fuse and replace if necessary or c.breaker reset.
5( Finally adjust the REED SWITCH , clean it and tight the plug very well see the diagram attached.
6) see the block attached. finally the display board can be faulty.
God bless you
10_1_2012_6_57_27_pm.gif10_1_2012_6_57_54_pm.gif

Nordic Track... | 939 views | 0 helpful votes


It plugs in on the side on the RHS of the console.

Nordic Track... | 30 views | 0 helpful votes


This will most possibly be a faulty console.
Is it under warranty ?

Nordic Track... | 60 views | 0 helpful votes


see my personal TIPS specially block diagram, if you will see the fuse for every treadmills.
2) Reset the c.breaker too.

3) Reset the c.breaker from your house outlet wall.
4) Test the power cord for wires, break, loose, or burn and repair.
5) Test the power switch, for open or shor. see the diagram attached.

sincerely. God bless you

Nordic Track... | 816 views | 0 helpful votes


see the video how to do it:God bless you


Nordic Track... | 95 views | 0 helpful votes


Download a manual for this model . This will make it easier to find the hidden screws.

Nordic Track... | 492 views | 0 helpful votes


I would call the retail shop and they will organize a repair man out to fix from Icon Fitness. This is done under warranty .

Nordic Track... | 404 views | 0 helpful votes


There can be a few reasons,
Lume
LCB
Console
Is it under warranty ?

Nordic Track... | 392 views | 0 helpful votes


http://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnes

11_17_2011_8_43_24_pm.gifsincerely. Please keep me in touch.

Nordic Track... | 1,584 views | 0 helpful votes


Adjusting the speed sensor:If the calibration does not pass you may need to check the speed sensoralignment.1) Remove the motor cover hood by loosening the 4 screws that hold it inplace (you do not need toremove them completely).2) The speed sensor is located on the left side of the frame, right nextto the front roller pulley (thepulley will have a belt around it that also goes to the motor). Thespeed sensor is small and blackwith a wire connected to it.3) Make sure the sensor is as close as possible to the pulley withouttouching it. You will see a magneton the face of the pulley; make sure the sensor is aligned with themagnet. There is a screw thatholds the sensor in place that needs to be loosened to adjust thesensor. Re-tighten the screw whenfinished.

GOOD LUCK.SINCERELY

Nordic Track... | 357 views | 0 helpful votes


Adjusting the speed sensor:If the calibration does not pass you may need to check the speed sensoralignment.1) Remove the motor cover hood by loosening the 4 screws that hold it inplace (you do not need toremove them completely).2) The speed sensor is located on the left side of the frame, right nextto the front roller pulley (thepulley will have a belt around it that also goes to the motor). Thespeed sensor is small and blackwith a wire connected to it.3) Make sure the sensor is as close as possible to the pulley withouttouching it. You will see a magneton the face of the pulley; make sure the sensor is aligned with themagnet. There is a screw thatholds the sensor in place that needs to be loosened to adjust thesensor. Re-tighten the screw whenfinished.



sincerely.

E.CUADRA
MANAGUA, NICARAGUA. C.A.

Nordic Track... | 288 views | 0 helpful votes

Not finding what you are looking for?
Nordic Track NordicTrack Commercial 1500 Treadmill Logo

65 questions posted

Ask a Question

Usually answered in minutes!

Top Nordic Track Exercise & Fitness Experts

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

135 Answers

Treadmill Repairs...
Treadmill Repairs...

Level 2 Expert

338 Answers

Android Man
Android Man

Level 2 Expert

278 Answers

Are you a Nordic Track Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Nordic Track Exercise & Fitness

  • Nordic Track Exercise & Fitness

Most Popular Question

nordictrack commercial 1500 treadmill w

  • Exercise & Fitness
Loading...