1) Lube the deck belt, this happen because the lack of maintenance according with the instr. manual. This produce shut down, for to protect the electronic system. Maybe you have a worn deck belt.3see the video and proceed according. LUBE the rollers bearings too.3) test the input voltage motor, and if there are voltage, the motor need repair.4) test the output voltage board, for input voltage motor, if there are NOT the board is faulty. see the diagram attached.God bless you
1) you must LUBE THE DECK BELT+ ROLLER BEARING.2) Test the input voltage motor, if there are the MOTOR is faulty need REPAIR.3) Test the output voltage board, for input voltage motor, if there are NOT the board is faulty. 4) SEE THE BLOCK DIAGRAM, whatever component can be faulty.However you must test the power cord for short circuit between cable, repair, and look inside according the BLOCK, and proceed with logic, see any loose wires, or some wires touching the carcase, some filter, coil, power supply USE the VOM. God bless you
see the block diagram: I recommend you to RUN the software calibration for diagnose, troublehooting, and fix it Before to exchange the control boar, maybe your have the motor for repair. or another section and the transformer for power supply.God bless you
yes YOU must RUN the software calibration, for diagnose and troubleshooting, read your instruction manual, if you do not have download fro free. www. fitness.manualsonline.com or www. iconservice.comGod bless you
1)Lube the deck belt,this is happening because the lack of lube produce enough friction between deck vs deck belt, and result in shut down.2)lube The rollers bearing very well3)measure the input voltage motor, if there are the motor need repair4) measure the output voltage board, for input voltage motor, if there are Not the board is faulty. see the bloc diagramGod bless you
1) Lube very well the deck belt, maybe you have deck belt worn by lack of maintenance schedule proceed with the instructio manuall , and adjust it.2) Test the drive belt and replace it.2a) LUBE the rollers bearing front, and rear3) Test the input voltage motor, if there are , the motor need repair.4) Test the output voltage board, for input voltage motor, if there are not the board is faulty.5) Try to run the software calibration for diagnose, and troubleshooting.sincerely. God bless you
1) Adjust the reed switch, clean, and tigh the connector wires very well. see the diagram attached.2) tigh the ribbon cables from keypad, clean it with special spray contact the keypads.. tight the wires connector from display board vs lower board.AFTERT your fix it RUN the s. caibrationGod bless you
Dear Sir:1) Lube the treadmill in according with the instruction manual.2) The reason is lack of lube by maintenance, that produce enough friction with shut down for to protect electronic system.3) Test the deck belt if is worn, and replace it.4) Test the rollers bearings5) See the bearing motor6) Test the input voltage motor coming from the output from the main motor board,, use DVOM.7) See my personal TIPS for HELP.sincerely. God bless you
if the plug is bend or something like. Try with some plyer to repair.Otherwise you need to replace the plug. You can go to www.fitnessrepairparts.com and to buy.Maybe you will need some electrician,if you do not have the experience.sincerely. God bless you
1) Adjust the Reed switch, see the diagram attached, clean, and tigh the wires connector very well.2) Tight the ribbon cables from keypads+ tight the wires connector from display board vs lower board. see the block diagram for better understanding. 3) Run the software calibration for diagnose, troubleshooting.God bless you
Dear Sir:Adjust the reed switch. see the attached diagram.proceed according with your instruction manual, if you do not have go for free download: www. fitness.manualsonline. com or www. iconservice. com sincerely. God bless you
Dear Sir:If you can the change the resistor is o.k ,depending about your skill in electricity or electronic.Remember when you change, but the exactly as indicated in the board. For example the resistor has color code, I can recomend you can buy some chart from Radio Shack, for you will see the exactly value+tolerance)Very Important+Power of resistor.Meanwhile, if the resistor is Sparking, is indicating there are some short-circuit in the board. By that reason when you change the resistor if the trouble persist, you must send the board or call some service tech from some company for assist you in this problemOther alternative that you have is RUN THE calibration SOFTWARE,that is coming with your equipment, the instruction most of them coming from the Hood of the motor, other your must use your Instruction Manual.This is important for easy Diagnose and Troubleshooting from your treadmill. Remember this very Complex equipment electronic.sincerely. God bless you.ernesto cuadramanagua, nicaragua. c.a
Dear Sir:There many possibilities: 1( False signal to due flexible cable loose *tight( 2( console display faulty 3(main motor board faulty 4(the pot attached to the elevation motor need adjustment 5( the gearing can sliping 6( Main motor damaged.Try to RUN the software calibration for easy diagnose and trouble.See my personal TIPS for HELP.sincerely. God Bless you.ernesto cuadramanagua, nicaragua. c.a
proceed according with your instruction manual, if you do not have go for free download: www. fitness.manualsonline. com or www. iconservice. com sincerely. God bless you
http://www.fixya.com/support/r10786838-test_procedure_dc_motor
sincerely. Happy New Year. G-d bless you.ernesto cuadramanagua, nicaragua. c.a.
