Top 20 Sony KDL60EX700 60 in. TV Questions & Answers

Check your owners manual for troubleshooting guide first. It could be something as simple as bad batteries in the remote.

it may be your TV is in a STORE DEMO mode, please check the set up menu, switch it back to HOME MODE.

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/ If blinks continue without any pause, the main board is faulty. Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

first i'd say try all the normal things... swap sources, check to see if the osd comes up, etcetera. it might just be that the tv isnt receiving a signal from the source its tuned to. see if theres a way to factory reset the tv, try it. if no matter what you do nothing shows up... maybe the backlight burned out or maybe something on the mb burned out. go over and sniff the tv, notice any smell? if this is the case, i dont suggest trying to fix it new screen.

Typical and serious fault. If you wish to get some details; check the site linked here. Pull up older posts.Surf the site with patience. Screen faults & possible causes to LCD screen are given with illustrations http://electronicshelponline.blogspot.com/

Hi 7 Times Blinking is for below reason TEMP_ERR Thermal Error FAN_ERR FAN Error (Not Detected. Display Only) Kind regards Rehan

Hello, The most likely solution to your problem is to go into the tv's settings and verify that the input (which ever the the number is) is not set to "skip" as that will make it appear as if it doesn't work. Just change the label for that input to anything but "Skip". Good Luck! I hope this helps. Rich Lilja

Hello, The most likely solution to your problem is to go into the tv's settings and verify that the input (which ever the the number is) is not set to "skip" as that will make it appear as if it doesn't work. Just change the label for that input to anything but "Skip". Good Luck! Rich Lilja

-Check your Manual look for something called blinking codes should be around page 9.-Please tell me you have a warranty, if not this can be expensive. Ranging from the main control board.- Have you tried cleaning bot ends of your LVDS Cables, this can sometimes remedy the problem.

And the problem would be WHAT?

Check its convergence adjustments. If you wish to get more details about how to do this, check this site. http://electronicshelponline.blogspot.com/ Pull up previous posts, either by type in the Brand name to your set in its search box, or view it in Mosaic / Timeslide / Flipcard option. Select view option by the drop-down view box, at the top left or the display window.

Hi 3 Times Blinking is for the following reason DC_ALERT -------> DC_ALERT DTT_WDT --------> DTT Error AUD_PROT -------> Audio Abnormal Detection Kind regards. Rehan

This could be a compatability issue. Check the manufaturer support site and look for the device compatability listingGood Luck Ed Pinero

Try this WEB site.http://www.nextag.com/sony-tv-stands/compare-html

That problem is usually have 2 causes..Its either power supply board or main board..

Please take this steps on how to determine the problem:
1. Open the back cover.
2. Check the power supply output...It should have 5vdc for the main board..12vdc or 16vdc for the audio and 24vdc for the back-light inverter..
3. If those 3 voltage supplies have encountered voltage drop...The problem could be on power supply board..
4. If the power supply output is normal..The problem could be on the main board...
5. If the problem is power supply you should check if the capacitors are bulged on the top and try to replaced it..If you can't do that you can purchased new power supply board..
6. If the problem is on main board there is no D.I.Y repair on that so you need to buy a new main board that fits to your TV..
Hope this solution will be helpful..

Thanks for using fixya...

Have you replaced the lamp?? The lamp may need to be replaced. Hope this helps.

Hi there, please get the code here : www.regionfreedvd.net/ www.dvdripper.org/dvd-region-codes-vs-ntscpal/ www.regionfreedvd.net/players.html
www.dvdreviewer.co.uk/Forums/...region_code/page1
Best Regards, Jay_mn093

if you have the remote you can do it from that, or menu CC display press until off

Software update to Current Version 4.020.

The problem in most of the case are: 1. Interference from a defective fluorescent lamp at your room sending signals to the infrared receiver of the TV. 2. Defective infrared receiver itself that sending noisy control signals to the CPU. 3. Defective manual control withes it has leakage. 4. Water damaged control switch PC board.