"Set" light when you're up to speed in Cruise control

Your best bet , take your vehicle to a qualified repair shop that has a professional scan tool an service repair info . So it can be diagnosed correctly . The Stop lamp switch is not a old school conventional type . Has three wires , five volt ref. voltage from the BCM ,
Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5-volt reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery positive voltage to the stop lamps, center high mounted stop lamp (CHMSL), transmission control module (TCM), and engine control module (ECM). Ground for the right rear stop lamp and CHMSL is applied at G402. Ground for the left rear stop lamp is applied at G400. The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.

Checking for DTC's - diagnostic trouble code's in the BCM would be my first diagnostic step , not guessing an replacing parts .

DTC B3903 02: Stop Lamp Relay Circuit Short to Ground
DTC B3903 05: Stop Lamp Relay Circuit Open or Short to Voltage

DTC C0277 06: Brake Pedal Position Sensor Circuit Short to Ground or Open
DTC C0277 07 : Brake Pedal Position Sensor Circuit Voltage Above Threshold
DTC C0277 09 : Brake Pedal Position Sensor Circuit Rate of Change Above Threshold

DTC C0278 00: Brake Pedal Position Sensor Not Calibrated

DTC C0870 03 : Device Voltage Reference Output 1 Circuit Voltage Below Threshold
DTC C0870 07 : Device Voltage Reference Output 1 Circuit Voltage Above Threshold
As you can see a number of DTC'S can be set , so do yourself a favor an let a qualified technician check it

Circuit/System Description
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5-volt reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery positive voltage to the stop lamps, center high mounted stop lamp (CHMSL), transmission control module (TCM), and engine control module (ECM). The stop lamps will not operate unless the ignition is in the ON position.

DTC P0572 : Brake Switch Circuit 1 Low Voltage
DTC P0573 : Brake Switch Circuit 1 High Voltage

It's hard to fix something when you don't have a clue how it works . The CC is also a controlled function of the BCM .
The BCM monitors the signal circuit of the cruise control switches. The BCM relays the cruise control switch status to the ECM via the GMLAN serial data circuit. The ECM uses the status of the cruise control switch to determine when to capture and maintain the vehicle speed. The ECM monitors the vehicle speed signal circuit in order to determine and the desired vehicle speed. The ECM uses the TAC motor in order to maintain the vehicle speed. For further review of the TAC system, refer to Throttle Actuator Control (TAC) System Description for the 2.0L engine or to Throttle Actuator Control (TAC) System Description for the 2.4L engine. Ignition voltage is supplied to the cruise control switch from the 2-amp CRUISE fuse located in the integrated BCM fuse block. The cruise control switches are located on the steering wheel. The cruise control function switches are arranged in a resistive ladder design, with each cruise control function switch having a different resistance value. The BCM detects a specific voltage value that is associated with any cruise control function switch being activated. When the normally open cruise control on/off switch is turned ON, the switch closes and the BCM detects a predetermined voltage signal on the cruise control set/coast and resume/accel switch signal circuit. The BCM sends a GMLAN serial data message to the ECM indicating that the On/Off switch is active. Similarly, when the + RES switch or the - SET switch are pressed, the BCM detects the predetermined voltage signal on the cruise control set/coast and resume/accel switch signal circuit. To engage the cruise control system, ensure that the vehicle speed is above 40.2 km/h (25 mph), turn the cruise On/Off switch ON and momentarily press the - SET switch. The ECM will engage the cruise control system and record the vehicle speed. The ECM sends a GMLAN serial data message via the BCM to the driver information center (DIC) in order to display the CRUISE ENGAGED message. The - SET switch or the + RES switch will remain inactive when the BCM has not received the predetermined voltage signal from the On/Off switch. Pressing the accelerator pedal, while the cruise control system is engaged, will allow the driver to override the cruise control system in order to accelerate the vehicle beyond the current set vehicle speed. When the accelerator pedal is released, the vehicle will decelerate and resume the current set vehicle speed. The driver can also override the current set vehicle speed via the - SET switch and the + RES switch. When the cruise control system is engaged, pressing and holding the - SET switch will allow the vehicle to decelerate from the current set vehicle speed without deactivating the cruise control system. When the - SET switch is released, the ECM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the cruise control system is engaged, momentarily pressing the - SET switch will allow the vehicle to decelerate at 1.6 km/h (1 mph) increments for each time that the - SET is momentarily pressed, with a minimum vehicle speed of 37 km/h (23 mph). Pressing and holding the + RES switch, when the cruise control system is engaged, will allow the vehicle to accelerate to a greater vehicle speed than the current set vehicle speed. When the + RES switch is released, the ECM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the cruise control system is engaged, momentarily pressing the + RES switch will allow the vehicle to accelerate at 1.6 km/h (1 mph) increments for each time that the + RES switch is momentarily pressed, with the maximum acceleration total of 16 km/h (10 mph) over the current set vehicle speed. Momentarily pressing the + RES switch after the cruise control system has been disengaged by pressing the brake pedal, will recall the previous set vehicle speed that is recorded in the ECM.

brake control switch ???? Define brake control switch ? Do you mean the switch on top of the brake pedal ? Brake light switch ? bake symbol stays??? Assume you mean brake symbol ? This is why you should have taken to a qualified repair shop. You probably have no idea as to how the cruise works . Your vehicle's cruise control is computer controlled . Vehicle has electronic throttle control , do you know what that is ? Before i get to technical , is the air bag light lit on the instrument cluster ? When you turn on the cruise does the cruise light turn on ? Taking the vehicle to a qualified repair shop that has a factory or professional type scan tool an checking for DTC'S - diagnostic trouble codes should be the first step in the diagnostic process . Not guessing an replacing parts . Do or did the brake lights work before or after switch replacement ? If so the switch wasn't bad.

The body control system consists of the body control module (BCM), communications, and various input and outputs. Some inputs, outputs and messages require other modules to interact with the BCM. The BCM also has discrete input and output terminals to control the vehicle's body functions. The BCM is wired to the GMLAN high speed serial data buss and the GMLAN low speed serial data buss and acts as a gateway between them. If the BCM does not communicate the vehicle will not start due to the inability of the engine control module (ECM)/powertrain control module (PCM) and theft deterrent module (TDM) to communicate without the BCM providing the gateway function.

Cruise Control Description and Operation
Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions at speeds above 40 km/h (25 mph). Steep grades may cause variations in the selected vehicle speeds.
The following are the main components of the Cruise Control System:
• The accelerator pedal
• The stop lamp switch
• The body control module (BCM)
• The cruise control switches
• The engine control module (ECM)
• The throttle actuator control (TAC) motor
• The vehicle speed sensor (VSS)

The body control module (BCM) monitors the signal circuit of the cruise control switches. The BCM relays the cruise control switch status to the engine control module (ECM) via the GMLAN serial data circuit. The ECM uses the status of the cruise control switch to determine when to capture and maintain the vehicle speed. The ECM monitors the vehicle speed signal circuit in order to determine the desired vehicle speed. The ECM uses the throttle actuator control (TAC) motor in order to maintain the vehicle speed. For further information on the TAC System, refer to Throttle Actuator Control (TAC) System Descriptionfor the 4.3L engine or Throttle Actuator Control (TAC) System Description for the 4.8L, 5.3L, 6.0L, 6.2L or 7.0L engines.
Voltage is supplied to the cruise control switch via the steering wheel control switch reference voltage circuit supplied by the BCM. The cruise control function switches are arranged in a resistive ladder design, with each cruise control function switch having a different resistance value. The BCM detects a specific voltage value that is associated with the cruise control function switch being activated. When the normally open cruise control on/off switch is turned ON, the switch closes and the BCM supplies a ground to the cruise control switch ON indicator circuit as it becomes illuminated. The BCM sends a GMLAN serial data message to the ECM indicating that the on/off switch is active. Similarly, when the normally open + RES switch or the normally open - SET switch are pressed, the switch closes and the BCM detects the predetermined voltage signal on the cruise control set/coast and resume/accel switch signal circuit. The BCM sends a GMLAN serial data message to the ECM indicating that the + RES switch or the - SET switch is active. To engage the Cruise Control System, ensure that the vehicle speed is above 40.2 km/h (25 mph), turn the cruise On/Off switch ON and momentarily press the - SET switch. The ECM will engage the Cruise Control System and record the vehicle speed. The ECM sends a GMLAN serial data message to the driver information center (DIC) in order to illuminate the CRUISE SET TO ### message. The ECM sends a GMLAN serial data message to the instrument panel cluster (IPC) in order to illuminate the Cruise Engaged indicator in the IPC. The - SET switch and the + RES switch will remain inactive when the BCM has not received the predetermined voltage signal from the on/off switch. Pressing the accelerator pedal, while the Cruise Control System is engaged, will allow the driver to override the Cruise Control System in order to accelerate the vehicle beyond the current set vehicle speed. When the accelerator pedal is released, the vehicle will decelerate and resume the current set vehicle speed. The driver can also override the current set vehicle speed via the - SET switch and the + RES switch. When the Cruise Control System is engaged, pressing and holding the - SET switch will allow the vehicle to decelerate from the current set vehicle speed without deactivating the Cruise Control System. When the - SET switch is released, the ECM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the Cruise Control System is engaged, momentarily pressing the - SET switch will allow the vehicle to decelerate at 1.6 km/h (1 mph) increments for each time that the - SET is momentarily pressed, with a minimum vehicle speed of 37 km/h (23 mph). Pressing and holding the + RES switch, when the Cruise Control System is engaged, will allow the vehicle to accelerate to a greater vehicle speed than the current set vehicle speed. When the + RES switch is released, the ECM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the Cruise Control System is engaged, momentarily pressing the + RES switch will allow the vehicle to accelerate at 1.6 km/h (1 mph) increments for each time that the + RES switch is momentarily pressed, with the maximum acceleration total of 16 km/h (10 mph) over the current set vehicle speed. Momentarily activating the + RES switch will recall the previous vehicle speed, after the cruise control system is disengaged by pressing the brake pedal or by activating the CANCEL switch.

Very highly doubtful that you could fix this .

Never use a higher amperage fuse in place of smaller amperage fuse . Could cause electrical fire's , burn the vehicle up. Besides that fuse is a low voltage input to the BCM - body control module . That wouldn't be the problem anyway , cruise control is computer controlled . You don't have the knowlege to fix this , your best bet , take it to a qualified repair shop . They would hook up a scanner that can view data , read code's . All your doing is guessing an that won't fix it. You have no clue of the complexity of the computer systems on your vehicle .

Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions at speeds above 40 km/h (25 mph). Steep grades may cause variations in the selected vehicle speeds.
The following are the main components of the cruise control system:
• The accelerator pedal
• The brake pedal position (BPP) sensor
• The body control module (BCM)
• The cruise on/off switch
• The + RES switch (equivalent to resume/accel switch)
• The - SET switch (equivalent to set/coast switch)
• The engine control module (ECM)
• The clutch pedal position (CPP) sensor, if equipped with a manual transmission
• The throttle actuator control (TAC) motor
• The vehicle speed sensor
The body control module (BCM) monitors the signal circuit of the cruise control switches, which are located on the steering wheel. The BCM relays the cruise control switch status to the engine control module (ECM) via the GMLAN serial data circuit. The ECM uses the status of the cruise control switch to determine when to capture and maintain the vehicle speed. The ECM monitors the vehicle speed signal circuit in order to determine the desired vehicle speed. The ECM uses the TAC motor in order to maintain the vehicle speed. For further information on the TAC system, refer to Throttle Actuator Control (TAC) System Description for the 2.2L engine or to Throttle Actuator Control (TAC) System Description for the 2.4L engine.
Ignition voltage is supplied to the cruise control switch from the 2-ampere EPS fuse located in the integrated BCM fuse block. The cruise control function switches are arranged in a resistive ladder design, with each cruise control function switch having a different resistance value. The BCM detects a specific voltage value that is associated with the cruise control function switch being activated. When the normally open cruise control on/off switch is turned ON, the switch closes and the BCM sends a GMLAN serial data message to the ECM indicating that the on/off switch is active. Similarly, when the normally open + RES switch or the normally open - SET switch are pressed, the switch closes and the BCM detects the predetermined voltage signal on the cruise control switch signal circuit. The BCM sends a GMLAN serial data message to the ECM indicating that the + RES switch or the - SET switch is active. The + RES switch or the - SET switch will remain inactive when the BCM has not received the predetermined voltage signal from the on/off switch.

Cruise Control on your vehicle is computer controlled , having the vehicle checked for DTC'S - diagnostic trouble codes should be the first step in diagnosing this problem . Not a code reader or autozone etc... Would need a factory Tech 2 scanner or someother professional type , one that can read BCM - body control module codes .
Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions at speeds above 40 km/h (25 mph). Steep grades may cause variations in the selected vehicle speeds.
The following are the main components of the Cruise Control System:
• The accelerator pedal
• The brake pedal position (BPP) sensor
• The body control module (BCM)
• The cruise control on/off switch
• The powertrain control module (PCM)
• The + RES switch
The + RES switch is the equivalent to an accel/resume switch.
• The - SET switch
The - SET switch is the equivalent to a set/coast switch.
• The throttle actuator control (TAC) module
• The TAC motor
• The vehicle speed sensor (VSS)

The odds of a fuse being the problem with a non operating cruise control are astronomical . Knowing how the cruise control works is a must in trouble shooting . The different modules involved ,the GMLAN serial data network etc... Here is the factory repair manual description .
Cruise Control Description and Operation
Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions at speeds above 40 km/h (25 mph). Steep grades may cause variations in the selected vehicle speeds.
The following are the main components of the cruise control system:
?€¢
The accelerator pedal

?€¢
The brake pedal position (BPP) sensor

?€¢
The body control module (BCM)

?€¢
The cruise on/off switch

?€¢
The + RES switch (equivalent to resume/accel switch)

?€¢
The - SET switch (equivalent to set/coast switch)

?€¢
The engine control module (ECM)

?€¢
The clutch pedal position (CPP) sensor, if equipped with a manual transmission

?€¢
The throttle actuator control (TAC) motor

?€¢
The vehicle speed sensor

The body control module (BCM) monitors the signal circuit of the cruise control switches, which are located on the steering wheel. The BCM relays the cruise control switch status to the engine control module (ECM) via the GMLAN serial data circuit. The ECM uses the status of the cruise control switch to determine when to capture and maintain the vehicle speed. The ECM monitors the vehicle speed signal circuit in order to determine the desired vehicle speed. The ECM uses the TAC motor in order to maintain the vehicle speed. For further information on the TAC system, refer to Throttle Actuator Control (TAC) System Description for the 2.2L engine or to Throttle Actuator Control (TAC) System Description for the 2.4L engine.
Ignition voltage is supplied to the cruise control switch from the 2-ampere EPS fuse located in the integrated BCM fuse block. The cruise control function switches are arranged in a resistive ladder design, with each cruise control function switch having a different resistance value. The BCM detects a specific voltage value that is associated with the cruise control function switch being activated. When the normally open cruise control on/off switch is turned ON, the switch closes and the BCM sends a GMLAN serial data message to the ECM indicating that the on/off switch is active. Similarly, when the normally open + RES switch or the normally open - SET switch are pressed, the switch closes and the BCM detects the predetermined voltage signal on the cruise control switch signal circuit. The BCM sends a GMLAN serial data message to the ECM indicating that the + RES switch or the - SET switch is active. The + RES switch or the - SET switch will remain inactive when the BCM has not received the predetermined voltage signal from the on/off switch.
Unless the air bag light is lit too , your best bet would be to take your vehicle to a qualified repair shop.

There is no fuse for Cruise Control , power is supplied by the BCM !
The body control module (BCM) monitors the signal circuit of the cruise control switches. The BCM relays the cruise control switch status to the engine control module (ECM) via the GMLAN serial data circuit. The ECM uses the status of the cruise control switch to determine when to capture and maintain the vehicle speed. The ECM monitors the vehicle speed signal circuit in order to determine the desired vehicle speed. The ECM uses the throttle actuator control (TAC) motor in order to maintain the vehicle speed. For further information on the TAC System, refer to Throttle Actuator Control (TAC) System Descriptionfor the 4.3L engine or Throttle Actuator Control (TAC) System Description for the 4.8L, 5.3L, 6.0L, 6.2L or 7.0L engines.
Voltage is supplied to the cruise control switch via the steering wheel control switch reference voltage circuit supplied by the BCM. The cruise control function switches are arranged in a resistive ladder design, with each cruise control function switch having a different resistance value. The BCM detects a specific voltage value that is associated with the cruise control function switch being activated. When the normally open cruise control on/off switch is turned ON, the switch closes and the BCM supplies a ground to the cruise control switch ON indicator circuit as it becomes illuminated. The BCM sends a GMLAN serial data message to the ECM indicating that the on/off switch is active. Similarly, when the normally open + RES switch or the normally open - SET switch are pressed, the switch closes and the BCM detects the predetermined voltage signal on the cruise control set/coast and resume/accel switch signal circuit. The BCM sends a GMLAN serial data message to the ECM indicating that the + RES switch or the - SET switch is active. To engage the Cruise Control System, ensure that the vehicle speed is above 40.2 km/h (25 mph), turn the cruise On/Off switch ON and momentarily press the - SET switch. The ECM will engage the Cruise Control System and record the vehicle speed. The ECM sends a GMLAN serial data message to the driver information center (DIC) in order to illuminate the CRUISE SET TO ### message. The ECM sends a GMLAN serial data message to the instrument panel cluster (IPC) in order to illuminate the Cruise Engaged indicator in the IPC.
If you don't know this I suggest you take your vehicle to the dealer or a ASE certified repair shop .

1. Disconnected or damaged vacuum lines to main cruise control unit;
2. Bad or misadjusted brake light switch (most likely);
3. Defective cruise control switch;
4. Failed main cruise control unit.

something in the system is not connected
could be the VSS, , clutch switch, brake switch, ignition control module

Here are the steps in using cruise control:

1. Get on a road you will be traveling at the same speed for a long period of time, such as a freeway.
   
2. Reach your desired speed. Choose a speed that allows you to move with the flow of traffic and not go over or under the designated speed limit for that road.
   
3. Locate the ON and SET buttons on your steering wheel. Press ON first and SET after. Your cruise control is now activated. Most vehicles must be traveling at least 30 miles per hour to set the cruise control.
   
4. Press and hold the SET button if you wish to use cruise control at a higher speed. Hold until your desired speed is reached.
   
5. Decrease speed by pressing the COAST button.
   
6. Push the brake pedal to disengage the cruise control function. If you wish to return to the previous set speed, use the RES (resume) button. You must be traveling at least 30 miles per hour for this function to resume.
   
7. Erase any previous speed by pressing the OFF button.