Question about Cars & Trucks

1 Answer

How to program replacement keyless entry remote for a 2006 Chevy Colorado?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 15,575 Answers

Dealer ! Unless you have a factory or professional scan tool .

Transmitter Programming
Important: Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly.
Important: All key fobs must be programmed each time any one fob is programmed. The scan tool must stay connected until all of the transmitters are programmed.
Install a scan tool and navigate to the BCM Module Setup menu.
Select Program Key Fobs.
Follow the scan tool on-screen directions.
When the programming operations have completed, operate the transmitter functions to verify correct system operation.

Posted on Oct 10, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: nissan murano 2005 sl keyless entry remote programing

Close all vehicle doors, LOCK doors using drivers side switch.

Insert key all the way into the ignition, (do not turn) remove key.

Repeat this step 5 times. (6 total)

Hazards should flash to indicate program mode.

Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.

*For additional remotes, cycle drivers door lock UNLOCK, LOCK, press any button on remote, hazards should flash. Repeat step as necessary.

Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.

Source

Posted on Aug 06, 2008

  • 1 Answer

SOURCE: program remote keyless entry

1) Turn key from OFF to ON eight times within 10 seconds ending in the ON position.

2) After doors lock then unlock, press any button on the
remote being programmed.

3) The doors should lock/unlock to confirm programming.

4) Turn key to OFF and door locks should cycle one last time.

Posted on Aug 17, 2008

emissionwiz
  • 85206 Answers

SOURCE: 2006 chevy equinox keyless remote programming

from the service manual:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Please go to the nearest GM dealer for assistance

Posted on Mar 26, 2009

Molson02536
  • 3854 Answers

SOURCE: programming a keyless entry remote

Key Fob Auto Learn
This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming. 

The vehicle must be OFF. 
Place the replacement key fob in the console pocket with the buttons facing forward. 
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds. 

The DIC will display a message: OFF/ACC TO LEARN. 
Press the OFF/ACC portion of the ignition button. 
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time. 
When the counter reaches 0, DIC will display OFF/ACC TO LEARN. 
Repeat steps 5-7 two more times, for a total of 30 minutes. 
The DIC will display a message: OFF/ACC TO LEARN. 
Press the OFF/ACC portion of the ignition button. 
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2. 
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode. 
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode. 
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation. 

Good luck and hope this help's keep me posted, there are 3 other methods and the 5th method is a tech 2 scan tool that the dealer uses but this should work on your year of cadillac. 

Posted on Jul 01, 2009

  • 7 Answers

SOURCE: program a keyless remote on a 2006 impala

push relearn again then press and lock and unlock for about ten seconds till u hear beep

Posted on Jul 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many wire harness clips connect to rcdlr module on 2007 impala besides the antenna


2007 Chevy Impala Keyless Entry: Keyless Entry Only ...

www.2carpros.com/questions/2007-chevrolet-impala-chevy-keyless-entry
Dec 30, 2010 - CHEVY KEYLESS ENTRY ... 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar. 5. ... Connect the new antenna to the RCDLR antenna module. 11.... The existing antenna is grounded into another wiring harness.

TPMS and key FOB range problems - LS1TECH

ls1tech.com/forums/ls4.../719926-tpms-key-fob-range-problems.html
May 24, 2007 - 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar.

Buick Workshop Manuals > Lucerne V6-3.8L (2007 ...


Dec 01, 2015 | 2007 Chevrolet Impala

1 Answer

How to program keyless entry remote for 2009 chevy malibu


Unfortunately your 2009 Chevy Malibu key fob does not have any self programming procedures. You have to have a professional program this key fob to your vehicle. I do have a couple money saving tips for you:

1) Purchase your Malibu key fob online at https://www.keylessentryremotefob.com/Chevrolet-Malibu-Remotes-and-Keys-s/3733.htm

2) Call a locksmith for programming. They are usually more affordable and they come to you.

Nov 20, 2013 | Chevrolet Cars & Trucks

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

Rear door lock won't lock or unlock on 2006 chevy colorado


could be door acuator switch. remove rear door cover follow rear door lock rod it will lead you to the lock motor check power plug make sure its its cliped in some times they come loose.next if plug is tight get a test lite chech see if you have power to lock motor have a friend move master switch up and down while youcheck for power mostlikely the switch is no good.

Apr 10, 2010 | 2006 Chevrolet Colorado

1 Answer

2006 Chevy Impala - Can't Clear Replace Battery in Remote Alarm


There is a fault code present and you will have to take it to a dealership for them to use a Tech II and read the code.

Jun 20, 2009 | 2006 Chevrolet Impala

2 Answers

Program fob


Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation

Apr 19, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

2006 chevy equinox keyless remote programming


from the service manual:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Please go to the nearest GM dealer for assistance

Mar 26, 2009 | 2005 Chevrolet Equinox

1 Answer

Keyless entry not working


Try re-programming the remotes, here is the procedure for your car.
JAGUAR
XJ8 Remote Control Programming
1. Unlock the trunk with key.
2. Turn Ignition on.
3. Warning light on dash comes on.
4. When they go out, lift arm rest, inside their is a valley button, Press 5 times within 5 secs of lights on dash going out, Horn & Lights Flash.
5. Press any button on remote, remote programmed

Dec 11, 2008 | 2006 Jaguar XJ8

1 Answer

2006 Chevy Equinox


Hiya...the factory-installed keyless remote control are installed in most Equinoxes IF SO equipped with this option that year.
However, it's difficult to get "true factory-installed" keyless feature in your Equinox ....but new 2008-2009 Equinoxes built this year now comes with standard keyless remote and yes, new option is remote STARTER feature (that option is identified by a black wire found inside the rear-right quarter window with thin metal line surrounding that interior window to receive signal from remote starter fob)

At least you can find after-market keyless remote control at your local retail store.

Sep 23, 2008 | 2006 Chevrolet Equinox

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22423 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...