Why doesn't left rear power window work?

2005 Chevrolet Tahoe Fuse Diagrams

Rick's Free Auto Repair Advice https://ricksfreeautorepairadvice.com > ... > Chevrolet

Sep 24, 2019 - 2005 Chevrolet Tahoe Fuse Diagrams for left instrument panel fuse box. 2005 Chevrolet Avalance fuse diagram left hand instrument panel.

Fuse Box Diagram Chevrolet Suburban / Tahoe (2000-2006)

Fuse-Box.info https://fuse-box.info > chevrolet > chevrolet-suburban...

It is located in the engine compartment on the driver's side of the vehicle next to the underhood fuse box. Fuse box diagrams. Advertisements.

https://www.google.com/search?q=2005+chevy+tahoe+sunroof+not+working

..

On the rear frame rail of the sunroof assembly. Approximately between the drivers and left rear passenger head. Imagine the sunroof window fully open and then add 2-3 inches. So above the left rear passengers lap.

If you want to solve your problem, click on the link I attach-

https://www.reliable-store.com/products/2012-honda-accord-tourer-workshop-repair-service-manual-pdf-download

No you don't need to remove the head liner to replace the switch . Here are the factory service repair manual directions .
Grasp the switch on the left and right sides. Use a small flat-bladed tool in order to disengage the clips which are located at the front and rear of the switch. Hold the flat-bladed tool parallel to the roof and push straight in. Rotate the switch toward the left side to disengage it from the mounting bracket and pull down. Disconnect the electrical connector from the switch. Remove the switch from the vehicle. This switch is supplied 5 volts from the sunroof module on the brown an orange wires ,the dark blue wire is grounded inside the sunroof module . The switch is just a low voltage input to the sunroof control module , The control module opens or closes the sunroof by the inputs from the switch . The odds the switch being bad are astronomical , more then likely the motor or the sunroof module are bad.
Your best bet would be to have a qualified repair shop diagnose the problem for you ! Do your power windows work ? Sun roof is powered by a circuit breaker an the windows are powered by the same circuit breaker .
There

Ford makes many vehicles with a sunroof and since I do not know you I will take a guess, try these llinks:

How to Repair an Ailing Sunroof

Ford Fusion Power Sunroof

Ford 150 FX4 Power Sunroof

Things to check when Power Rear Sliding Window doesn work Ford F150 Forum

You can't put up the front passenger window with it's own switch ? Did you check the POWER WINDOW RELAY in the instrument panel fuse / relay box ? An you checked POWER fuse 30amp same fuse box ? All window switches have direct power from power window relay !
Fuse Block - Instrument Panel
Left of the Steering Column, behind the storage Compartment
P/W Relay
--
Sunroof Switch Assembly, Window Switch - Left Front, Window Switch - Left Rear, Window Switch - Right Front, Window Switch - Right Rear

Sounds like you have already diagnosed the problem, Denise.
Replace the broken switch and go from there.

Check your wires and fuses, I am having a similar problem myself as the windows open, but not the sunroof and this is a feature that VW had on most of these models with power locks, even my 96 Gti did it. I will repost with what fixed it ASAP.

The sunroof is powered by the same circuit breaker that power's your power window, so if your windows work than the circuit breaker should be good. You needed test the switch to verify if works with; on the factory sunroof system the roof is controled by a sunroof module the module receives a signal from the switch then throws voltage to the sunroof motor. The motor and module are located between the sunroof assembly and windshield underneath the head liner. You would reconnected the switch and test to see if the sunroof motor is getting power when the switch is in use by testing the dark green wire when closing and a light green wire when opening. Test these wires at the sunroof motor with a ohm meter or test light. Also, check this procedure to repair...

GM S-Series Pick-ups and SUV's 1994-1999 Repair Guide Power Sunroof - REMOVAL & INSTALLATION

Glass

1. Close the sunroof and open the sunshade.
2. If the piece of glass being removed is to be reinstalled, mark the location of the screws, this will ensure proper alignment during installation.
3. Unfassten the screw that attach the sunroof glass to the sunroof assembly.
4. Remove the glass from the vehicle.
   

To install:

1. Place the glass into position and install the screws that retain the glass. Do not fully tighten the screws just yet.
2. Adjust the glass so that the fit between the glass and the opening is equal at all four sides. The rear edge of the glass may be slightly higher than the front edge to reduce the wind noise.
3. After the glass has been adjusted, tighten the screws to 31 inch lbs. (3.5 Nm).
4. Check the operation and fit of the glass.
   

Motor

1. Disconnect the negative battery cable.
2. Remove the sunroof opening trim by starting at the **** joint and pulling the trim strip from the sunroof opening.
3. Remove the headlines as follows:
   1. If equipped, remove the overhead or sunroof console.
   2. If equipped, remove the dome lamp.
   3. Remove the coat hooks and the assist handles.
   4. Remove the sunshade-to-roof screws, while pulling down on the sunshade base, push in on the extended screws, loosen the screw that attaches sunshade to the roof and pull down on the sunshade retainer while pushing in on the extended screw. Remove the retainer.
   5. Remove the windshield garnish moldings using trim removal tool J 38778 or its equivalent. Pull the molding away from the pillar and up to remove it.
   6. On four door models, remove the body lock pillar trim panels.
   7. Remove the roof rear header garnish molding using the trim removal tool. Insert the tool into the front edge of the trim and work along the front of the panel, from one end to the other. Unplug the cargo lamp electrical connection and remove the trim.
   8. On two door models, remove the rear seat upper seat belt anchor bolts.
   9. Remove the upper and lower front seat belt anchor bolts.
   10. Remove the rear seat belt lower anchor nut (two door models only).
   11. Remove the end gate or liftgate opening sill plate.
   12. Remove the jack storage cover (left side).
   13. Remove the upper body side trim panel screw (left side).
   14. Remove the upper body side trim panel and the body side front lower trim panel.
   15. Remove the headliner from the vehicle.
4. Remove the sunroof console mounting bracket.
5. Remove the straps that retain the wiring harness.
6. Tag and unplug any necessary electrical connections.
7. Unfasten the screws that attach the motor to the sunroof assembly.
8. Remove the motor from the vehicle. Make sure that you do not move the sunroof mechanism while the motor is not in place.
   

To install:

1. Place the motor into position and install the retaining screws. Tighten the screws to 31 inch lbs. (3.5 Nm).
2. Attach all electrical connections that were unplugged.
3. Attach the straps that retain the wiring harness.
4. Install the sunroof console mounting bracket.
   

New headliners must be pierced to accommodate actual vehicle accessories.

1. Install the headliner as follows:
   1. Install the body side front lower trim panel and the upper body side trim panel.
   2. Install the upper body side trim panel screw (left side).
   3. Install the jack storage cover (left side).
   4. Install the end gate or liftgate opening sill plate.
   5. Install the rear seat belt lower anchor nut (two door models only). Tighten to 59 ft. lbs. (80 Nm).
   6. Install the upper and lower front seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
   7. On two door models, install the rear seat upper seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
   8. Install the roof rear header garnish molding. Attach the cargo lamp electrical connection, place the trim in position and engage the molding retainers.
   9. On four door models, install the body lock pillar trim panels.
   10. Install the windshield garnish moldings. Place the molding into position, align the retainer clips with the slots and press into place.
   11. Place the sunshade retainer in position, install the screw and tighten to 10 inch lbs. (1.1 Nm). Position the sunshade, install the screws and tighten to 10 inch lbs. (1.1 Nm).
   12. Install the coat hooks and the assist handles.
   13. If equipped, install the dome lamp.
   14. If equipped, install the overhead or sunroof console.
       
2. Install the sunroof opening trim. Start the trim in the center of the front of the sunroof opening and work around the perimeter.

Hope helps (remember rated this) Good luck.

hope this helps. if u have any other questions just let me know




Fuse locations for options not shown can be found in the corresponding wiring diagrams.
Amp.


1 - Headlight, Low Beam, Left (56b) 10
2 - Headlight, Low Beam, Right (56b) 10
3 - License Plate Lights (5 10
4 - Rear Window Wiper And Washer System 15
5 - Windshield Wiper/Washer 15
6 - Fresh Air Blower, A/C (X) 20
7 - Tail Lights, Right (58R) 10
8 - Tail Lights, Left (58L) 10
9 - Rear Window Defogger 20
10 - Fog Lights 15
11 - Headlight, High Beam, Left (56a) 10
12 - Headlight, High Beam, Right (56a) 10
13 - Horn (15) 10
14 - Back-Up Lights 10
15 - Engine Electronics (15) 10
16 - Power Sunroof, Front Map/Reading Light 15
17 - Emergency Flashers (15) 10
18 - Fuel Pump (FP), Heated Oxygen Sensor (HO2S)
Control Module 20
19 - Coolant Fan, A/C Relay (30) 30
20 - Brake Lights (30) 10
21 - Interior Lights, Clock, Luggage Compartment
Light (30) 15
22 - Cigarette Lighter, Radio, Luggage Compartment
Release 10

Separate Fuses

(Located above the relays)



- Fuse for ABS hydraulic pump relay 30
- Fuse for ABS main relay 30
- Fuse for A/C 30
- Fuse for power windows 20
- Fuse for cruise control 5
- Fuse for cigarette lighter 15