1994 Chevrolet Suburban - Answered Questions & Fixed issues
Keeps draining battery on 1994 chevy suburban
In most cars & truck with this problem, the most common reason is a defective alternator.
In the meantime, unhook that battery each time you stop the truck to prevent dead batteries.
Suburban running rough under load
their are quite a few reasons --needs tune-up--bad gas--throttle body clogging failing--cat converter failing--egr valve carboned up -fuel filter -these are a few
When braking and almost to a complete stop for
Anti-Lock Braking System (ABS)
Purpose Anti-lock brake systems (ABS) - generally also referred to as anti-lock
systems (ALS) - are designed to prevent the vehicle wheels from locking
as a result of the service brake being applied with too much force, especially
on slippery road surfaces.
The idea is to maintain cornering forces on braked wheels to ensure that
the vehicle or vehicle combination retains its driving stability and manoeuvrability
as far as physically possible. The available power transmission
or grip between tyres and carriageway should also be utilised as
far as possible to minimise the braking distance and maximise vehicle
deceleration.
Why ABS? Although today commercial vehicle brakes are designed to a very high
technical standard, braking on slippery roads often results in potentially
dangerous situations. During full or even partial braking on a slippery
road it may no longer be possible to fully transfer the braking force onto
the road due to the low coefficient of friction (friction coefficient (k)) between
the tyres and the carriageway. The braking force is excessive and
the wheels lock up. Locked wheels no longer provide any grip on the
road and are almost incapable of transferring any cornering forces
(steering and tracking forces). This often has dangerous consequences:
- The vehicle becomes unsteerable
- The vehicle breaks away in spite of countersteering, and starts to
swerve.
- The braking distance is significantly increased
- Tractor-trailer combinations or semitrailer trains may break away or
jackknife.
Load sensing valve influence On dry roads today's load sensing valves (ALB) alone are often capable
of preventing the wheels from locking if the vehicle is unladen; they also
help the driver to effectively grade the braking process on wet road surfaces,
but they are unable to prevent locking as such (no slip monitoring).
In addition, they are unable to counteract any overreactions on the
part of the driver, or any variances in frictional or adhesion coefficients
which may apply to different sides of the vehicle, or indeed to its different
axles (?-split road surfaces).
Benefits of ABS: Only the Anti-Lock Brake System (ABS)
- guarantees stable braking characteristics on all road surfaces.
- maintains steerability and generally reduces the braking distance
- prevents vehicle combinations from jackknifing
- reduces tyre wear.
Limits of ABS Although ABS is an effective safety device, it can not suspend the limits
defined by driving physics. Even a vehicle fitted with ABS will become
uncontrollable if driven too fast around a corner.
So ABS is not a licence for a maladjusted style of driving or failure to observe
the correct safety distance.
4
ABS Training Anti-Slip Regulation (ASR)
Anti-Slip Regulation (ASR)
Why ASR? Increasing the engine output (accelerating) on a slippery road surface
can easily lead to the maximum adhesion on one or all powered wheels
being exceeded causing them to spin, especially if the vehicle is unladen
or partially laden.
Spinning wheels when driving off or accelerating represent a safety risk
just like locked wheel do when braking.
Reasons - Wheels that spin transfer just as little cornering force as locked
wheels.
- They also no longer transfer any tractive power onto the road.
Consequences - Vehicles that do not move or get stuck.
- Vehicles that can no longer be steered, jackknife on uphill uphill
gradients, or swerve in corners.
Benefits of ASR ASR prevents the powered wheel from spinning and provides the following
benefits:
- Tractive power and cornering forces are maintained.
- Stable driving behaviour is ensured when moving off, accelerating
and negotiating corners on slippery roads.
- The indicator lamp (if installed) is used to warn the driver of slippery
road conditions.
- Tyre wear is reduced to a minimum, and the motor vehicle's drive
train protected
- The risk of accidents is further reduced.
ASR and ABS: ASR represents a worthwhile addition to an ABS-controlled braking system.
All that is required to turn ABS control into full ABS/ASR control is
an ECU with the additional ASR function and a few additional components
for controlling the differential brake and the engine. This why ASR
is only available in combination with ABS.
Even a differential lock for off-road use and ASR do not exclude but complement
each other.
Limits of ASR The traction capacity of an all-wheel driven commercial vehicle can not
be achieved by a motor vehicle with only one driving axle - not even with
optimal ASR.
Engine dies
if it shuts off while driving down the road. and restarts after 10 minutes, its usually a bad crank sensor that does this. it messes up timing and shuts off fuel supply.
Truck starts with a boost but once cables are off battery indicator drops then truck shuts down unless engine is revved.
Check the alternator and the charging system. You may have a weak or failing alternator. If you have a voltmeter, get the battery reading with the engine off. A charged, good battery should show at least 12.6 volts. If you have to boost it, it must be low on charge. Recharge it or have it tested, a dead cell in the battery would not let it charge up.
Now take a reading on the battery with the engine idling, or idling as low as possible without dying. A good alternator and charging system will make the battery now read at least 13.5 volts. If your reading is lower than this, you probably have a weak alternator.
I need a bleeding sequence for a 1994 GMC Suburban
The proper sequence to bleeding any brakes, are usually to do the one farthest away from the master cyl. first, and continue till ur at the last one. (left front). Rear brakes, then to the front brakes!
How to adjust brake pedal light switch
brake pedal switch the long part of the switch should touch brake pedal arm.in which turn off brake lights, when press brake pedal this will cause closed circuit and brake lights will turn on.
Not finding what you are looking for?