20 Most Recent 2009 GMC Canyon Questions & Answers


The cam solenoid may be bad/worn out or the screen is blocked causing this code . States vary on emissions.

2009 GMC Canyon | Answered on Aug 16, 2017


What engine ? 2.9 - 3.7 - 4.8 - 5.3 L An do you mean- crankshaft position (CKP) sensor ? My GM service info shows only one on each of these engines ! What kind of problem are you having ? A no start - no spark ?

2009 GMC Canyon | Answered on Aug 06, 2015


P0000 don't know p2444 secondary air injection system pump stuck on bank 1

2009 GMC Canyon | Answered on Apr 11, 2015


Sounds like the blend door is stuck in the heat position OR the temperature controller is not operating the hot water valve.

2009 GMC Canyon | Answered on Dec 31, 2014


- Secondary Air Injection (AIR) System Shut-Off Valve Stuck Open

2009 GMC Canyon | Answered on Feb 20, 2014


Measure the nut in fractional size & divide by .0395
Then you will have your metric axle nut size.
34,36mm etc.

One would assume you work on your own vehicles,that you
have all the sockets, in 1/2" drive, from 10 thru 36mm

2009 GMC Canyon | Answered on Jun 01, 2012


Yes the wheels will accept this tire size easily.

2009 GMC Canyon | Answered on Sep 16, 2011


locate your owners manual,all fluid types and capacities are listed.

2009 GMC Canyon | Answered on Dec 31, 2009


you have to start by removing the trim around the radio. it just pulls towards you then unplug connector (if any). Remove three 7 mm bolts from the radio mounts. Radio will just pull out. Not if you replacing it with aftermarket. there is now acc wire in the harness and the ignition switch is to weak to power this wire so the use of a GMRC01 from metra electronics will work perfect to supply you with all the connections needed for the aftermarket hookup

2009 GMC Canyon | Answered on Sep 02, 2009


Reduced Power means that the PCM has detected an active failure in either the engine, transmission or brake system. You The PCM reduced power to help protect an affected system. You need to start by checking the oil level. How was the engine running and the transmission shifting? Do you have a code reader? The codes need to be retrieved. Please write back with the codes. Good Luck.

GMC Canyon Cars... | Answered on Oct 24, 2018


You must scan the system with a special tool as it is computer controlled.

GMC Canyon Cars... | Answered on Oct 10, 2018


When battery voltage is lost, sometimes there are some modules that may need to be reprogrammed? It could effect your security system, where applicable. I don't know model year?
If it cranks good but won't start, make sure battery has a full charge. Have a helper crank it while you check for spark at the plugs. Also, check proper fuel pressure and fuel injector pulse. Find out what your missing, if anything?

GMC Canyon Cars... | Answered on Mar 17, 2018


If the check engine light was on DTC'S - diagnostic trouble code's should be stored . If the light was on , disconnecting the battery won't do anything . Diagnostic's need to be done . Sounds like you have no clue , so best advice , take it to a qualified repair shop .

GMC Canyon Cars... | Answered on Jan 07, 2018

Not finding what you are looking for?
2009 GMC Canyon Logo

Popular Tags

28 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Canyon GMC

  • Canyon GMC

Most Popular Question

getting engine codes seem find out mean

  • Cars & Trucks
Loading...