Hyundai Elantra - Recent Questions, Troubleshooting & Support - Page 4

you pay to have it repaired

A screwdriver, but you need the target board that garages have. From a certain distance on flat ground, the beam has to hit the board in a certain way.

There's a small rubber pad which sits on the brake pedal arm, and holds the brake light switch OFF when the pedal is released. When this rubber pad falls off, the brake light switch is on all the time, not just when the pedal is pressed down. Find the rubber pad, and glue it back on, or make a replacement from cardboard, duct tape, whatever.

Videos here https://www.google.com/search?q=2013+hyundai+elantra+clutch+adjustment ..

You need someone with a programming scan tool. https://www.programyourremote.com/classified/2017-hyundai-elantra-keyless-entry-remote-fob-smart-key-programming-instructions-listing-8720.aspx ..

There is a video here https://www.google.com/search?q=replace+a+tail+light+in+a+2016+Hyundai+Elantra ..

https://www.fixya.com/cars/t29804314-adjustment_screws_2017_hyundai_elantra

Can anyone mark on this fuse box for FOG lights for Elantra 2015. There isnt too much about it on the internet.

https://www.cargurus.com/Cars/Discussion-t66940_ds1068808

P0310 Cylinder 10 Misfire DetectedP0710 Transmission Fluid Temperature Sensor CircuitP1700 Transmission Indeterminate Failure (Failed to Neutral)______________BMW ICOM ISIS ISID

there is no cut off swich if you want to disable it remove the back seat, there is an access plate for the fuel pump remove the plate and unplug the pump there is main ecu relay under the dash along with many other relays its hard to find tho

3 layer head gaskets torque to 22 ft/lb then 60°-65° then 60°-65°again.
2 layer head gasket torque to 18 ft/lb then 60°-65° then 60`-65° again

About L.B signal i fix it with more than 12 avante cars just remove the gage tableau and remove the built under r phars then you will never see this problem again and for more details you can call me any time +962786742552

Bolt pattern? Like which bolts do you tighten in which order? -always tighten opposite bolts sequentially

Well Strauss told you wrong. You can replace just the fuel filter without replacing the fuel pump. And you are in luck because on your Hyundai there is an access panel which allow you to access the fuel pump without removing the fuel tank. Read the warnings and heed them. Work in well ventilated area with all windows on the vehicle down, disconnect the battery before starting this repair, and use every precaution to not have any sparks near where you are working. Click the link for detailed instructions with photos. Please be very careful and do not attempt this unless you feel confident you can accomplish this repair. http://www.elantraxd.com/forums/showthread.php?t=17699

Hmmm.... rear strut bushings.

it depends. we need to know a lot more like: -oil weight used -when does it happen (morning,afternoon) -does it happen when hot or cold -are you driving it offroad if you had a shortblock replaced at 8000km that tells me something about YOUR driving habits and how you maintain a vehicle

look for the metal rod the handle is attached to. you should be able to move that back and forth (latching and unlatching), with pliers, if you can reach it

inspect the threads, one might be crushed. try pulling up while turning so the threads engage

camshafts don't have torque. the answer you really want depends on the question you are asking. you need to clarify: 1- are you asking about torque generated at the CRANKSHAFT? 2- which country are you in? this dictates your engine specs 3- are you asking about the torque applied to the camshaft hold down button?